UNIRAC EcoFoot5DTM Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 29

UNIRAC EcoFoot5DTM Скачать руководство пользователя страница 15

INSTALLATION GUIDE

PAGE

HIGH DENSITY 5-DEGREE

BALLAST RACKING SYSTEM

12

EcoFoot5D Bases can be tucked under the north edge of the north row and connected to anchored Strut. Strut runs East/West. See diagram below.

• Do not use Mid Supports and Ballast Trays on

north row of tucked EcoFoot5D Bases.

• An additional EcoFoot5D Base may be added to

the center of the module frame if required for
high snow loads. The additional center Base does
not need to be attached to the Strut.

Method B: EcoFoot5D Bases Attached

METHOD B: EcoFoot5D BASE TUCKED ON NORTH EDGE

DETAIL A:
Roof Attachment

DETAIL B:
Tucked EcoFoot5D Base on North Edge

NOTE:
Some EcoFoot5D arrays are designed to be fully

attached with strut running North/South. For fully

attached systems, Mid supports and Ballast Trays

are not needed. North edge Bases can be tucked and

additional East/West strut attachment is not needed.

SYSTEM INSTALLATION STEPS

«
...
13
14
15
16
17
...
»

Содержание EcoFoot5DTM






























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды