background image

The HPL110A functions in these examples are as follows:

P - 

Power %kW:

The display shows true power in units of % of full scale for the 

HPL110A as installed.

Ts -  Start Delay Timer:

Ts is used to delay the start of active monitoring until after 

the start surge is completed.

The HPL110A assumes that the motor is OFF when  measured load - %kW - is 

below 5% full scale.  The Ts timer starts when the load reaches 5% and 

monitoring is disabled for the duration of the Ts period.  Ts is programmable 

in the range 0.1 to 99.9 seconds.

On conclusion of the Ts period, monitoring becomes active. 

If P drops below 5%, monitoring is immediately disabled and a new Ts period 

will start as soon as load again reaches 5%.

L1 -  Max. Limit:

Max. alarm limit programmable in the range 5% to 100% / OFF 

and used in conjunction with the Tr1 Reaction Timer. A Max. Limit alarm is tripped 

if P exceeds L1 for a period Tr1.

Tr1 -  Reaction Timer:

Used in conjunction with the L1 Max. Limit and programmable 

in the range 0.0 to 99.9 seconds. Tr1 is time for which the P must remain above 

the L1 Max. Limit before an alarm is declared.  If P falls below the L1 during the 

Tr1 timer period, the timer is re-set to zero.

Note:

if Tr1 is set to 0.0 seconds, actual reaction time will be one cycle or approx. 

16 msec. at 60Hz and 20 msec. at 50Hz

L2 -  Min. Limit: 

Min. alarm limit programmable in the range OFF / 5% to 100% and 

used in conjunction with the Tr2 Reaction Timer.  A Min. Limit alarm is tripped 

when P remains below the L2 Min. Limit for a period of time Tr2.

Tr2 -  Reaction Timer: 

Used in conjunction with the L2 Min. Limit and programmable 

in the range 0.0 to 99.9 seconds.  Tr2 is time for which the P must remain below 

the L2 Min. Limit before an alarm is declared.

- Max. 

Level:

If the 

up arrow key is depressed while the HPL110A is in monitor 

mode, the display will show the maximum load - in %kW - experienced since 

the last Ts.

Ñ 

-  Min. Level:  

If the 

Ñ 

down arrow key is depressed while the HPL110A is in monitor

mode, the display will show the minimum load - in %kW - experienced since the 

last Ts.

5

Содержание HPL110/220





















Отзывы: