manualshive.com logo in svg

Unimotion STDF EC Series, Руководство пользователя

Поделиться
Скачать
Unimotion STDF EC Series Скачать руководство пользователя страница 44

 

 

 

44/108 

 

8) of Status word become SET and the Push Motion is executed. Target position refers to the 
Target  position  (607Ah)  and  Position  value  can  be  absolute  coordinates  or  relative 
coordinates by Control word of Relative (Bit 6). In the Push Motion (Non-stop Mode), the Push 
Motion is not finished even if a work is detected or the target position is reached. the Push 
Motion is finished when Halt (Bit 8) of Control word becomes SET. 

 

 

Figure 4-8: Push Motion (Non-stop Mode). 

 

1. A work was detected. The detection status can be judged by Push Detected (Bit 14) of the 
Status word. 

2. It continues the Push Motion when work disappears. 

3. The target position is reached. But the Push Motion is not finished. 

4. When Halt (Bit 8) of Control word becomes SET, the motor stops, and the Push Motion is 
finished. the Target Reached (Bit 10) of Status word becomes SET after finished the Push 
Motion. 

 

Содержание STDF EC Series













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды