Unigas HR75A MG Series Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 66

background image

PART II: INSTALLATION

15

MOUNTING AND CONNECTING THE BURNER

Transport and storage

If the product must be stored, avoid humid and corrosive places. Observe the temperatures stated in the burner data table at the begin-
ning of this manual.

Handling the burner

The burner is mounted on a stirrup provided for handling the burner by means of a fork lift truck: the forks must be inserted into the A
anb B ways. Remove the stirrup only once the burner is installed to the boiler.

ATTENTION! The equipment must be installed in compliance with the regulations in force, following the manufac-
turer’s instructions, by qualified personnel. All handling operations must be carried out with appropriate
resources and qualified personnel

ATTENTION: Use intact and correctly dimensioned hoisting equipment, conforms to the local regulations and
health and safety regulations. Do not stand under lifted loads.

Packing

The burners are despatched in wooden crates whose dimensions are:

1672mm x 1072mm x 1016mm (L x P x H)

Packing cases of this type are affected by humidity and are not suitable for stacking.
The following are placed in each packing case:

z

burner with detached gas train;

z

gasket or ceramic fibre plait (according to burner type) to be inserted between the burner
and the boiler;

z

envelope containing this manual and other documents.

z

oil flexible hoses;

To get rid of the burner’s packing, follow the procedures laid down by current laws on disposal
of materials.

ATTENTION! The handling operations must be carried out by specialised and trained personnel. If these
operations are not carried out correctly, the residual risk for the burner to overturn and fall down still persists.

To move the burner, use means suitable to support its weight (see paragraph “Technical specifications”).

The unpacked burner must be lifted and moved only by means of a fork lift truck.

PART II: INSTALLATION

H

P

L

A

B

«
...
13
14
15
16
17
...
»

Содержание HR75A MG Series



































































Отзывы:

Нет отзывов

Похожие инструкции для HR75A MG Series

LAMTEC BT3 Series

Бренд: Unigas Страницы: 137

Бренд: Jaxon Страницы: 40

Бренд: Greenheck Страницы: 40

Бренд: baltur Страницы: 52

Бренд: baltur Страницы: 66

Бренд: baltur Страницы: 74

Бренд: baltur Страницы: 104

Бренд: Hauck Страницы: 2

Бренд: Riello Страницы: 20

Бренд: Yunca Gas Страницы: 4

Бренд: Wolf Страницы: 2

Бренд: XTline Страницы: 16

Бренд: Ferroli Страницы: 232

Бренд: Cal Flame Страницы: 36

Бренд: Wayne Страницы: 25

Бренд: URBAN FIRES Страницы: 21

Бренд: PROPOINT Страницы: 24

Бренд: PROPOINT Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды