Unigas HR75A MG Series Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 66

Unigas HR75A MG Series Скачать руководство пользователя страница 45

PART III: OPERATION

45

Double-stage burners

1

Once the air and gas flow rates are adjusted, turn the burner off, switch the

CM

switch to the heavy oil operation (OIL, on the bur-

ner control panel.

2

with the electrical panel open, prime the oil pump acting on the related

CP

contactor (see next picture): check the pump motor rota-

tion and keep pressing for some seconds until the oil circuit is charged;

3

start the burner up by means of the thermostat series;

4

bleed the air from the

M

pressure gauge port (Fig. 24) by loosing the cap without removing it, then release the contactor.

Fig. 24

5

drive the burner to high flame stage, by means fo the thermostat

TAB

(high/low flame thermostat - see Wiring diagrams).

6

the nozzle supply pressure is already factory-set and must not be changed. Only if necessary, adjust the supply pressure as fol-
lows (see related paragraph); insert a pressure gauge into the port shown on Fig. 25 and act on on the pump adjusting screw

VR

(see Fig. 38) as to get the nozzle pressure at 20bar (Monarch or Fluidics nozzles - see page 36).

7

the oil flow rate in the high flame stage is the maximum pressure with the return line closed

8

To adjust the

air flow rate in the high flame stage

, loose the

RA

nut and screw

VRA

as to get the desired air flow rate: moving

the rod

TR

towards the air damper shaft, the air damper opens and consequently the air flow rate increases, moving it far from the

shaft the air damper closes and the air flow rate decreases.

Note:

once the procedure is perfomed, be sure that the blocking nut

RA

is fasten. Do not change the position of the air damper

rods.

9

drive the burner to low flame by means of the

TAB

thermostat.

10 To perform the regulation, remove the cap

D

and loosen the screw

V

(see Fig. 40), by means of a screwdriver (see Fig. 40). The

regulating screw

V

acts on the return pressurefrom the nozzle. Set the pressure to the minimum value of 5 bar. Read the values on

the pressure gauge placed on the regulator’s coupling

M

. Once the regulation is accomplished, replace cap

D

.

Suntec E7

HP Technik UHE

Suntec TA.

Note:

After a certain operating period, the pressure can change because of some dirt on the needle’s seal: remove the screw

VT

(see Fig. 38) and clean.

CP

VR

M

VR

M

VR

M

VRA

RA

TR

«
...
43
44
45
46
47
...
»

Содержание HR75A MG Series



































































Отзывы:

Нет отзывов