background image

 

SAFETY INSTRUCTIONS  

When working with the winch you need to observe the safety instructions! 

 
In order to prevent accidents carefully read and observe the following instructions: 

 

1.

 

General: 

 
1.

 

Apart  from  the  instructions  in  this  user  manual  you  should  also  observe  all  general 
safety and accident preventing regulations. 

 

 

 
2.

 

When working with the winch, it is necessary to comply with the rules of safety at work. 

3.

 

Only persons, who are older than 18, are allowed to work with the winch. 

4.

 

Safety and warning plates on the machine provide important instructions for safe use. 
Observe them for your safety. 

5.

 

The  winch  or  its  flawless  operation  should  be  checked  before  every  use  or  at  least 
once every working day. Defects should be removed by an expert. Before first use or 
after significant alterations and at least once a year the winch must be examined by 
an expert. 

6.

 

When using public transport routes observe traffic signs and regulations. 

7.

 

When  using  the  winch  wear  personal  protective  equipment(helmet,  gloves, 
appropriate footwear,...). 

8.

 

Before starting and driving check the surrounding area (children). Maintain adequate 
visibility. 

9.

 

Riding on the winch during transport is not allowed. 

10.

 

Connect the winch according to the instructions. 

11.

 

For on road travel the machine must be in the following condition. If the winch covers 
the rear lights of the tractor and they are not visible during  transport on public roads, 
install additional lights on the winch. 

12.

 

 Adjust the driving speed to the environmental conditions. When driving up or down or 
across a slope avoid sudden turning of the steering wheel. 

13.

 

 Do not stand in the danger area. 

        

 

 

Содержание 45M



































Отзывы: