Uniden UBCT-9 Скачать руководство пользователя

Страница: 56 / 68

Care and Maintenance

General Use

• Turn the scanner

OFF

before disconnecting the power.

• Always write down the programmed frequencies in the event of memory loss.

• If memory is lost, simply reprogram each channel.

The display shows 000.0000 in all channels when there has been a memory loss.

Location

• Do not use the scanner in high-moisture environments such as the kitchen or bathroom.

• Avoid placing the unit in direct sunlight or near heating elements or vents.

• If the scanner receives strong interference or electrical noise, move it or its antenna

away from the source of the noise. If possible, a higher elevation may provide better

reception.

Cleaning

• Disconnect the power to the unit before cleaning.

• Clean the outside of the scanner with a mild detergent.

To prevent scratches, do not use abrasive cleaners or solvents. Be careful not to rub

the LCD window.

• Do not use excessive amounts of water.

Repairs

• Do not attempt any repair. The scanner contains no user serviceable parts contact your

retailer or see warranty page for service information.

Birdies

• All radios can receive birdies (undesired signals). If your scanner stops during Scan

mode and no sound is heard, it may be receiving a birdie. Birdies are internally

generated signals inherent in the electronics of the receiver.

Press

L/O

to lockout the channel, and then press

HOLD/RESUME

to resume scanning.

UBCT9 OM 52

12/11/07 3:54:04 PM

Содержание UBCT-9





































































Результаты поиска

Содержание UBCT-9

Отзывы:

Похожие инструкции для UBCT-9

Бренды по названию

Популярные бренды

Uniden UBCT-9, Руководство пользователя

Результаты поиска

Содержание UBCT-9

Отзывы:

Похожие инструкции для UBCT-9

Бренды по названию

Популярные бренды