Uniden UBCT-9 Скачать руководство пользователя

Страница: 14 / 68

Typical Mounting Methods

The UBCT9 can be conveniently mounted on a table, bulkhead, overhead, or any other

desired location with the supplied mounting bracket (refer to figure below for typical

mounting methods).

Caution:

Make sure there are no hidden electrical wires or other items behind the

desired location before proceeding. Check that free access for mounting and

cabling is available.

• Table top mount

• Bulkhead mount

• Overhead mount

Mounting the Scanner in Your Vehicle

Before you mount the scanner, make sure you have all the necessary materials. Then

confirm that the scanner fits your vehicle’s mounting area. This unit requires a mounting

area of 50.8mm high by 176.5mm wide by 153.6mm deep.

Caution:

Be sure to avoid obstructions behind the mounting surface.

Follow these steps to mount the scanner in your vehicle.
1. Choose a mounting location, then use the supplied

mounting bracket as a template to mark the positions

for the mounting screw holes.

2. In the marked positions, drill holes slightly smaller

than the supplied screws.

3. Attach the mounting bracket to the mounting location

using the supplied screws and lock washers.

4. Attach the scanner to the mounting bracket using the

supplied mounting knobs.

5. Connect the antenna’s cable to the

ANT.

connector

on the rear of the scanner.

Note: If the antenna cable’s connector does not fit in

the

ANT

connector, you might also need a

Motorola-to BNC antenna plug adapter

(available at a local electronics store).

UBCT9 OM 10

12/11/07 3:52:53 PM

Содержание UBCT-9





































































Результаты поиска

Содержание UBCT-9

Отзывы:

Похожие инструкции для UBCT-9

Бренды по названию

Популярные бренды

Uniden UBCT-9, Руководство пользователя

Результаты поиска

Содержание UBCT-9

Отзывы:

Похожие инструкции для UBCT-9

Бренды по названию

Популярные бренды