background image

-  3  -

 4-1. 유수판 설치 / Ins talling the oil pan

 

   1. 두부 쿠션②를 유수판① 모서리에 삽입 시키십시오. 

   2. 두부 쿠션③을 유수판① 모서리에 삽입 시키십시오.

  

   1.  Insert  the  two  head  cushions②  into  the  front  corner  of  the       

       oil pan①.

   2.  Insert  the  two  head  cushions③  into  the  back  corner  of  the       

       oil pan①. 

  

 3. 작업 테이블의 유수판 홈에 일치되게 정열 삽입 하십시오.

  

   3. Place the oil pan① into the groove in the work table so

     that corners are aligned.

   4. 2개의 힌지 쿠션 고무④를 테이블의 홈 부에 삽입 시키십시오.

 

   4. Insert the two rubber cushions④ into the notches in the

   

   5. 무릎 올림대⑤를 그림의 위치에 삽입 시키십시오.

   5. Insert the knee lifter⑤ complying bar.

4-2. 무릎올 림장치 설치 / Installing the knee lifter as sembly

 

   1. 무릎올림 장치 조립품①을 유수판의 무릎올림 레바축②에 결합 

      시킨 후 볼트③를 완전히 체결해 주십시오. 

     

※ 

무릎올림 장치 조립품①의 무릎 올림 판의 위치를 조절하여 

        사용하기 전 편한 위치를 선정하십시오. 

   1. Place the knee lifter assembly① onto the knee lifter bar② on  

      the oil pan, and then secure it by tightening the bolt③

     

※ 

Adjust the position of the knee lifter plate① so that it is  

        easy to use.

                                               

All manuals and user guides at all-guides.com

Содержание DB2-H515











































Отзывы: