Unical CoR C24 Скачать руководство пользователя

Страница: 48 / 52

service

PARASITE FLAME

Flame detected upon ignition

Check the wiring of the Ign/Det.

electrode and remove any oxidation.

Check for humidity between drain wire

and ceramic, if necessary, replace

the electrode, press the unblock key,

if the anomaly persists, replace the

electrode (4).

FIAMMA PARASSITA

Fiamma rilevata dopo lo spe

gnimento

Verificare il cablaggio ed even

tuali perdite della valvola gas

(3) event. sostituire Valv. gas.

(F) 27

ERROR

Flow Gradient

Check if the pump switches off

suddenly.

(F) 23

Detected tab panel button pres-

sed for longer than 30 “

Check keypad and reset the

status of the buttons. Or repla-

ce the electronic board

(F) 53

Clogged Outlets

Check the Chimneys / Check

the trap.

BLOCK

Control circuit problems

Gas Valve

Check the Gas Valve connec

tions / Replace the Gas Valve

(3)

/ Replace the Modulation

Board

BLOCK

Gas Valve opening time beyond

limit time

Check the parts that generate

the heat requests (thermostats,

electrovalve limit switches, flow

switch, etc.)

Flame loss

Check the electrode and its wi-

ring to check the gas pressure

at minimum power, if neces-

sary re-calibrate.

BLOCK

General block for unclassified

anomalies.

Replace Modulation Board.

ERRORS DISPLAYED ON REGOLAFACILE ONLY

Regolafacile external sensor

Replace the external probe /

Regolafacile

Regolafacile Internal Sensor

Replace Regolafacile

Eprom Error of Regolafacile

Replace Regolafacile

service

Содержание CoR C24





















































Результаты поиска

Содержание CoR C24

Отзывы:

Похожие инструкции для CoR C24

Бренды по названию

Популярные бренды

Unical CoR C24, Руководство по установке и обслуживанию

Результаты поиска

Содержание CoR C24

Отзывы:

Похожие инструкции для CoR C24

Бренды по названию

Популярные бренды