Unical CoR C24 Скачать руководство пользователя | Manualshive

Страница: 27 / 52

background image

27

ENGLISH

Installation Instructions

Switching boiler on and off

NOTE!

Further details in the section

‘‘Technical Information’’ on the boiler

page of the www.unicalag.it website

Commissioning must be done by profes-

sionally qualified personnel. Unical AG

S.p.A. will not be held liable for damage

to persons, animals or objects due to

failure to comply with the above instruction.

Before commissioning the boiler, check that:

3.10 - COMMISSIONING

does the installation meet the specific standards and regulations in force, both relating to the

gas part as well as the electrical part?

do the combustion air intake and flue gas exhaust take place properly according to what is

defined by the specific rules and regulations in force?
is the fuel supply system sized according to the capacity required by the boiler?

Is it equipped with all safety and control devices required by the standards in force?

is the power supply of the boiler 230V - 50Hz?

has the system been filled with water (approximately 0.8/1 bar pressure on the pressure gauge

with the pump stopped)?

are any system shut-off gate valves open?

does the gas to be used correspond to the boiler calibration gas?: otherwise, perform the boiler

conversion in order to use the gas available (see section: 4.3”);

this operation must be carried out by technical staff qualified in compliance with the standards in force;
is the gas supply valve open?

has the system been checked for gas leaks?

is the outside main switch ON?

is the system safety valve efficient and is it connected to the drains?

is the condensation drain trap connected to the drains?
has the system been checked for water leaks?

are the ventilation conditions and minimum distances to perform any maintenance

ensured?

have the GAS, HEATING and DOMESTIC HOT WATER pipes been cleaned thoroughly with

products suitable for each circuit?

has a surveillance and protection system against gas leaks been installed? (Optional)

are the system pipes NOT used as the electrical system earthing?

has the system been sized properly bearing in mind the radiator pressure drops?

thermostatic valves, radiator stop valves

has the operator been trained and has the documentation been supplied?

Please tick the operations performed

«
...
25
26
27
28
29
...
»

Содержание CoR C24





















































Отзывы:

Нет отзывов

Похожие инструкции для CoR C24

Бренд: QHT Страницы: 52

LOGIC HEAT2 H12

Бренд: Ideal Heating Страницы: 8

LOGIC COMBI2 C24

Бренд: Ideal Heating Страницы: 10

Salamander Broiler

Бренд: U.S. Range Страницы: 52

Бренд: REMEHA Страницы: 44

Бренд: Bakers Pride Страницы: 24

ITACA CH KR 105

Бренд: Fondital Страницы: 104

Wessex ModuMax mk3 WM116/116H

Бренд: Hamworthy Страницы: 68

Бренд: ideal commercial Страницы: 28

Бренд: Effecta Страницы: 43

Бренд: Trianco Страницы: 23

INDEPENDENT C30

Бренд: IDEAL Страницы: 72

Бренд: Centrometal Страницы: 40

Бренд: Aerco Страницы: 108

Бренд: Embassy Страницы: 80

Бренд: PENSOTTI Страницы: 81

Бренд: Truma Страницы: 28

Бренд: Truma Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды