background image

Chapter 2.  Warnings and Safety Instructions.

Read these instructions carefully before operating, maintaining or servicing this tool.
Please keep these instructions in a safe accessible place.

Read to fully understand and 
observe the following safety 
precautions and warnings.
Careless or improper use of this 
equipment may result in serious or
fatal injury.

Always wear eye, head and ear
protection equipment, when 
using this tool

Operator Safety

!

Always read the instructions carefully so as 
to avoid any injury or damage when 
unfamiliar with this equipment.

!

Always wear a safety face shield or goggles.

!

Wear ear defenders when using this 
equipment.

!

Always wear heavy clothing, boots and 
gloves. Do not wear loose clothing, short 
pants, sandals etc. and ensure that long hair is
tied up above shoulder length.

!

Do not operate this equipment when tired, ill 
or under the influence of alcohol, drugs or 
medication.

!

Never allow an inexperienced person operate
this equipment.

!

 Never operate the equipment in damp, or 
water logged area.

!

Keep all carrying handles and levers free 
from oil.

!

Keep hands away from the cutter when it is 
rotating. Ensure that it has stopped rotating 
and is disconnected from the power source 
before touching the cutter.

Tool Safety

!

Inspect the entire piece of equipment 
before use. 

!

Replace damaged components, lubricate 
where necessary and ensure that all 
fasteners are secure.

!

Always use a safety chain to secure the 
equipment when it is being used above the 
ground.

!

Use only accessories that have been 
recommended by the manufacturer. Failure
to do so could result in damage to the tool 
and may invalidate the warranty.

         WARNING!

Never modify the tooling any way. Do not use 
your equipment for any job other than for 
which it is intended.

Maintenance safety

!

Maintain according to the manufacturers 
recommended procedures.

!

Disconnect the equipment from the power 
source before attempting any maintenance.

!

Use only genuine replacement components 

WARNING!

Indicates instant possibility of 
severe personal injury or loss of 
life, if instructions are not 
followed.

CAUTION!

Indications a possibility of 
personal injury or equipment 
damage, if instructions are not 
followed.

4

Содержание BD35

















Отзывы: