UNI-T UPO2000CS Series Скачать руководство пользователя | Manualshive

Страница: 68 / 94

background image

UPO2000CS series User Manua

67

•

LRR: Time between the last rising edge of source 1 to the last rising edge of source 2

•

LFR: Time between the last falling edge of source 1 to the last rising edge of source 2

•

LFF: Time between the last falling edge of source 1 to the last falling edge of source 2

8.5 User Defined Parameters

Press the MEASURE button to enter the automatic measurement menu. Then press the F1 key to select the source
of the measurement. The user defined parameter selection interface can be chosen by F4.

User Defined Parameter Selection

Adjust the parameters with the multipurpose knob, press the multipurpose knob button to confirm selection. For
every selected parameter, a * symbol will appear in front of the parameter.

F3 can be pressed to turn off user defined parameter selection menu and the parameters will be display at the

bottom of the screen. For convenience and immediate view of these parameters, up to 5 parameters can be defined
at the same time.

Users can also choose to open the measurement statistical function with the F4 key.

«
...
66
67
68
69
70
...
»

Содержание UPO2000CS Series































































































Отзывы:

Нет отзывов

Похожие инструкции для UPO2000CS Series

Бренд: Baker Hughes Страницы: 168

Бренд: Yamaha Страницы: 78

Бренд: Fast Страницы: 42

Бренд: DARAY Страницы: 28

Бренд: Backyard Play Systems Страницы: 64

Бренд: Haenim Страницы: 2

WJHD309 - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 7

WJ-ND300 Administrator Console

Бренд: Panasonic Страницы: 24

Бренд: Konica Minolta Страницы: 32

Бренд: Mackie Страницы: 34

Бренд: Mackworth Страницы: 38

Бренд: P&P Страницы: 6

Бренд: PAS Systems International Страницы: 24

MARK V Alcovisor

Бренд: PAS Systems International Страницы: 20

Бренд: PARRY Страницы: 14

Бренд: York Fitness Страницы: 36

Бренд: H&S Страницы: 54

Бренд: Samson Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды