UNI-T UPO2000CS Series Скачать руководство пользователя

Страница: 5 / 94

UPO2000CS series User Manual

eneral Safety Overview

This instrument strictly complies with the safety requirements for electronic measuring instrument GB4793 and

IEC 61010-1 safety standard during design and manufacturing. Please understand the following safety

preventative measures, to avoid personal injury, and to prevent damage to the product or any connected

products. To avoid possible dangers, be sure to use this product in accordance with the regulations.

Only trained personnels can perform the maintenance program.

Avoid fire and personal injury.

Use the correct power line:

Only use the dedicated UNI-T power supply appointed to the local region or

country for this product.

Correct Plug:

Don't plug when the probe or test wire is connected to the voltage source.

Ground the product:

This product is grounded through the power supply ground wire. To avoid electric shock,

grounding conductors must be connected to the ground. Please be sure that the product is properly grounded

before connecting to the input or output of the product.

Correct connection of oscilloscope probe

Ensure that the probe ground and ground potential are correctly

connected. Do not connect ground wire to high voltage.

Check all terminal ratings

To avoid fire and the large current charge, please check all the ratings and the

marks on the product. Please also refer to the product manual for details on the ratings before connecting to

the product.

Do not open the case cover or front panel during operation

Only use fuses with ratings listed in the technical index

Avoid circuit exposure

Do not touch exposed connectors and components after power is connected.

Do not operate the product if you suspect it is faulty, and please contact UNI-T authorized service personnel for

inspection. Any maintenance, adjustment, or replacement of parts must be performed by UNI-T authorized

maintenance personnels.

Maintain proper ventilation

Please do not operate the product in humid conditions

Please do not operate in inflammable and explosive environment

Please keep the product surface clean and dry

Содержание UPO2000CS Series































































































Результаты поиска

Содержание UPO2000CS Series

Отзывы:

Похожие инструкции для UPO2000CS Series

Бренды по названию

Популярные бренды

UNI-T UPO2000CS Series, Руководство пользователя

Результаты поиска

Содержание UPO2000CS Series

Отзывы:

Похожие инструкции для UPO2000CS Series

Бренды по названию

Популярные бренды