background image

FACT: 
UnderCover's 
ABS-Composite 
material makes 
it the strongest 
and most 
durable tonneau 
on the market.

 

Installation of the front bracket is very similar to the rear. Remove the plastic plugs exposing the 3 

preset bolt holes located at the front of the bed.  

Page 8, Picture A

 shows how the front bracket will look 

once it is fully installed.

 

Position the front bracket over the three preset bolt holes. See 

Page 8, Figure 1

. Attach the bracket 

to the truck using the three 6mm bolts and washers. The measurement is just a starting point, the brackets 
are slotted to allow for adjustment. See 

Page 8, Picture B

. Tighten the three bolts using a 10mm wrench 

or socket/ratchet. See 

Page 8, Picture C

. BE SURE NOT TO OVER TIGHTEN OR YOU COULD SHEAR OFF THE 

BOLT HEAD CREATING A VERY DIFFICULT PROCEDURE TO REMOVE THE REMAINING THREAD.

 

Repeat process for other side.

 

Now you are ready to set your cover on the truck. The hinge that is attached to the cover has slots in 

it that fit over the mounting posts on the bracket you just installed. See 

Page 8, Figure 2

.

 

With the hinge slot over the post, the cover will be sitting about 1-inch past the tailgate. See

 Page 9, 

Picture F

. With the cover sitting all the way down on the truck bed, push the cover forward securing the 4 

bar hinge to the mounting posts. See 

Page 9, Picture G.

 

With some assistance, have someone hold the cover up at the rear and reach inside the cover and 

screw in the two fastening knobs.  See 

Page 9, Picture H

.

A

B

C
D

E

F

WARNING!  Be sure not to over tighten the rear mounting bolts. Doing so could shear 
off the bolt heads, creating a difficult procedure to remove the remaining thread.

FORM # IG2110HH

Modified Mar 2009

Page 7

Model 2110 Ford Explorer Sport Trac 2007-Current 

Содержание 2110

















Отзывы: