Ulvac SGT-100 Скачать руководство пользователя страница 11

Страница: 11 / 13

10. Caution
Prior to operation, read this manual carefully and operate the pump using with great care

and responsibility. When installing to the SGT process, take necessary measure s to
prevent from damaging the equipment.

<Other>
If any abnormality such as defective condition is found in the equipment, stop the

operation immediately and contact your local agency or ULVAC KIKO.

11.

Trouble shooting

Trouble symptom

How to check Result

Corrective

action

Pressure difference
Large

Replace the element

Check pressure
difference between
inlet and outlet side

Pressure difference
None

Able to use

Large

Cleaning is required
also check the
element ensure that
no clogging.

①

Element is

clogged

Check the particle at
INLET pipe flange
parts (Visual look)

Small

Continue to use

Bad corrosion
and partly coming off

Replace the housing

②

corrosion of the

inside housing

Visual look

Corrosion only

Continue to use

Check the element
According to item

①

According to item

①

According to item

①

Good

O-ring is satisfactory

O-ring (upper lid)

Damage, crack and
hardening

Replace O-ring

Good Satisfactory

･

SGT leak check for

piping system

Unsatisfactory Repair

Foreign body

Remove

③

Vacuum

performance is not
satisfactory

Check the foreign
body (visual look)

No foreign body

Satisfactory

※

Element is completely sealed with degas condition by ULVAC KIKO.
Open the package just before using SGT-100, 200.

Содержание SGT-100














Результаты поиска

Содержание SGT-100

Отзывы:

Бренды по названию

Популярные бренды

Ulvac SGT-100, Инструкция по эксплуатации

Результаты поиска

Содержание SGT-100

Отзывы:

Бренды по названию

Популярные бренды