Ultraflex ND1-MM Скачать руководство пользователя

Страница: 9 / 40

ZTF SYSTEM

page 9

of 39

Installation manual

ULTRAFLEX

2.1 General warnings

2 TRANSPORTATION

The product weight with its packaging is around 20kg (44 lbs.). Therefore, it can be handled manually.

2.2 Packaging contents

Before using the equipment check that the product has not been damaged during transportation. Make also sure

that all the standard components are in the packaging. In case of damage, do not use the ZTF Tiller System and

notify the freight carrier and your dealer/distributor immediately.

The ZTF Tiller System is provided with the following items:

WARNING

The staff in charge of handling must operate with protective gloves and safety shoes.

Main system

Accessory kit based on installation type, (see the following chart with related drawings and paragraph 3.2)

Hoses

Valve assembly

Cylinder

MERCURY

YAMAHA

SUZUKI

KIT ND1-MM

(75-115 HP

ENGINES)

KIT ND1-Y

(90-115-130 HP

ENGINES FROM

2015)

KIT QU1-Y

(150-175-200 HP

ENGINES)

KIT QU1-S

DF150A / 175A /

200A ENGINES)

PROVIDED IN THE KIT

1. Bracket

2. Hardware fastening the device to the bracket (2

screws M12, 2 nuts, 4 washers)

3. Hardware fastening the cylinder link arm to the

engine arm (2 special bolts ULTRABOLT, 2 high

nuts, 4 washers)

4. Hardware fastening the cylinder link arm to

the engine arm (1 SVS bolt ULTRABOLT, 1 SVS

washer, 1 thin nut)

5. Hardware fastening the bracket to the engine

arm (2 pivots, 2 washers, 2 nuts)

CAUTION: this hardware is always included in

Yamaha tiller handles
6. Hardware fastening the cylinder link arm to

the engine arm (1 SVS bolt ULTRABOLT, 1 SVS

washer, 1 thin nut)

7. Hardware fastening the bracket to the engine

arm (2 screws, 2 washers) CAUTION: washers

always included in Mercury Marine tiller handles

8. 2 Caps

9. Throttle cables and shift cables

Содержание ND1-MM









































Результаты поиска

Содержание ND1-MM

Отзывы:

Похожие инструкции для ND1-MM

Бренды по названию

Популярные бренды

Ultraflex ND1-MM, Руководство по установке

Результаты поиска

Содержание ND1-MM

Отзывы:

Похожие инструкции для ND1-MM

Бренды по названию

Популярные бренды