Ultraflex ND1-MM Скачать руководство пользователя

Страница: 34 / 40

Installation manual

ULTRAFLEX

page 34

of 39

- ZTF SYSTEM

Proceed as follows:

1. Move the cylinder towards the end of stroke on the

starboard side (see picture 1) by steering the tiller
handle in the same way as during navigation.

NOTICE

The by-pass knob must be fully loosened (system in by-
pass mode).

2. Start the Bubble Buster by pressing the switch shown

below.

3. The oil will start circulating into the system and, from the two transparent hoses connected to the cylinder,

oil together with air will start flowing.

4. Without moving the tiller handle and, therefore, the cylinder, wait for a couple of minutes until the transparent

hoses show only oil with very few air bubbles.

5. Move the cylinder slowly towards the opposite side (port, see picture 2), by always acting on the tiller handle.

4.2.2 Filling and purging operation

TOWARDS

STARBOARD

5. Loosen the release nuts (3) for enabling the oil to pass through. Do not unscrew more than one turn and a

half. Use a 16 mm wrench.

6. Connect the battery clamps: the red clip to the positive terminal and the black one to the negative terminal.

CAUTION

Only 12 Vdc power supplies are allowed.

Содержание ND1-MM









































Результаты поиска

Содержание ND1-MM

Отзывы:

Похожие инструкции для ND1-MM

Бренды по названию

Популярные бренды

Ultraflex ND1-MM, Руководство по установке

Результаты поиска

Содержание ND1-MM

Отзывы:

Похожие инструкции для ND1-MM

Бренды по названию

Популярные бренды