background image

SYSTEM PROGRAMMING - 

Menu 1

PAGE 4

80 SERIES

INSTALL  MANUAL

 QUICK VIEW WIRE DIAGRAM

1
2
3

1
2
3

1
2
3
4

THERMISTOR/ INPUT TRIGGER TO START****

 

The thermistor can be installed in the engine compartment for engine temperature or in 
under the dash for interior temperature. Must be connected prior to power-up to be
detected by the remote starter. 

Position 1 or  Position 2

BLACK**

GREEN**

BLUE**

GREEN

BLUE

N/A*

RED

BLACK

WHT/VIOLET

RED**

BYPASS MODULE DATA COMMUNICATION PORT***

The default setting is for idatalink modules. For Fortin bypass modules power-
up the system with the Fortin module connected to the data port to set the default
to Fortin bypass module.

1
2
3
4

SELECTABLE PARK LIGHT OUTPUT*****

                   

GROUND OUTPUT FOR ADDITIONAL SENSOR (-)

FULL TRIGGER FOR ALARM MODELS (-)

PRE-WARN TRIGGER FOR ALARM MODELS (-)

OUTPUT TO ACTIVATE DOOR LOCK CIRCUIT (-)

OUTPUT TO ACTIVATE DOOR UNLOCK CIRCUIT (-) 

OUTPUT FOR VOLTAGE INVERTER*

12VOLT OUTPUT FOR BYPASS MODULE 

GROUND OUTPUT FOR BYPASS MODULE

(-) WHILE RUNNING OUTPUT (BYPASS TURN ON) 

12VOLT OUTPUT FOR ADDITIONAL SENSORS (+)

BY DEFAULT THE SYSTEM COMES WITH 
THE PARK LIGHT JUMPER SET FOR 
POSITIVE PARK LIGHT OUTPUT.

 TO CHANGE THE SYSTEM TO A NEGATIVE 
PARK LIGHT OUTPUT, PLACE THE JUMPER 
IN THE NEGATIVE PARK LIGHT POSITION 
SHOWN IN THE DIAGRAM. 

(Position 2)

POSITIVE
PARK LIGHT

NEGATIVE
PARK LIGHT

SYSTEM PROGRAMMING - 

Menu 1

PAGE 5

INSTALL MANUAL

NOTES

  

PLEASE NOTE

* THE CENTRE PIN OF THE KEYLESS CONNECTOR IS LOW CURRENT AND IS 
DESIGNED TO SUPPLY POWER TO DOOR LOCK MODULES (DO NOT CONNECT TO 
RELAYS) OVERLOADING THIS OUTPUT WILL DAMAGE THE MODULE!

**THIS CONNECTOR IS USED FOR ALARM MODELS ONLY. A GROUND PULSE TO THE 
BLUE WIRE WILL CAUSE THE ALARM TO BEEP 3 TIMES. A GROUND PULSE TO THE 
GREEN WIRE WILL CAUSE THE ALARM TO ACTIVE FOR 60 SECONDS. THIS INPUT 
CAN BE USED FOR AN ADDITION SENSOR SUCK AS A RADAR, GLASS BREAK OR 
AN EXTRA SHOCK SENSOR. THIS INPUT IS TURNED ON AND OFF WITH THE MAIN 
SHOCK SENSOR.

***THIS INPUT IS USED TO CONNECT BYPASS MODULES USING THE DATA TO DATA 
TYPE CONNECTION. THERE ARE 2 SELECTION TYPES. 

THE DEFAULT SETTING IS 

FOR IDATALINK MODULES. THE SECOND IS FOR FORTIN BYPASS MODULES. IF THE 
BYPASS KIT IS A IDATA PRODUCT SIMPLY CONNECT TO THIS INPUT AND PROGRAM 
THE BYPASS MODULE AS PER THE INSTRUCTIONS. WHEN INSTALLING A FORTIN 
BYPASS MODULES POWER-UP THE STARTER/ALARM WITH THE FORTIN MODULE 
ALREADY CONNECTED TO THE DATA PORT THEN PROGRAM AS PER THE 
INSTRUCTIONS.

****THE THERMISTOR WILL DETECT THE ENGINE OR INTERIOR TEMPERATURE OF 
THE VEHICLE AND TRIGGER THE VEHICLE TO START WHEN IN COLD START MODE.
THE THERMISTOR MUST BE CONNECTED PRIOR TO POWER UP TO BE DETECTED 
BY THE UNIT.

*****ALWAYS TEST AND CONFIRM THE PARK LIGHT POLARITY BEFORE MAKING 
YOUR CONNECTION TO THE VEHICLE.

MANUAL TRANSMISSION VEHICLES MUST BE INSTALLED USING A MANUAL 
TRANSMISSION MODEL. CONNECT THE PARK BRAKE AND DOOR PIN WIRES TO 
THE SYSTEM.

REMOTE STARTER. NEVER INSTALL A AUTOMATIC MODEL INTO A MANUAL 
TRANSMISSION VEHICLE.

80 SERIES

Содержание 80 Series





















Отзывы: