Installation Guide
PROGRAMMING
9
1
Chrysler / VW Re-Arm
1 Flash
Unlock pulse before start and a lock pulse after start
2
GM Auto Re-Lock
2 Flashes
Lock pulse after remote starter shuts off
3*
Normal Operation
3 Flashes
No additional re-lock pulses
1
Diesel Glow Plug
1 Flash
W
2
Timed Delay
2 Flashes
Ignition ON for 10 seconds before engaging remote starter
3*
Gas Mode operation
3 Flashes
Waits 2 seconds before engaging starter output
aits a Maximum of 3:20 second before starting.
1
Type 1
1 Flash
Pulse after start and with lock
2
Type 2
2 Flashes
Pulse after start only
3*
Factory Re-arm 3 Flashes
0.75 second pulse with lock and after shutdown
Press the Program Switch 1 time
to select setting 1 (This will be confirmed by 1 LED flash)
Press and hold the Prog
ram Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program.
Press the Program momentarily to move to next program step or repeat to change selection.
Press the Program Switch 2 times
to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Program
Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch.
Press the Program momentarily to move to next program step or repeat to change selection.
Press the Program Switch 3 times
to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Program
Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch.
Press the Program momentarily to move to next program step or repeat to change selection.
Setting 1- Special Door Lock/ Unlock Operations
Setting 2- Gas/ Diesel Mode-
Blue Wire on 14-Pin
Setting 3- Rearm Output-
Yellow Wire on 14-Pin
1
30 Min Run Time
1 Flash
Remote Starter runs for 30min when activated
2
45 Min Run Time
2 Flashes
Remote Starter runs for 45min when activated
3*
15 Min Run Time
3 Flashes
Remote Starter runs for 15 min when activated
1
10 Seconds
1 Flash
10 sec Max time that starter will stay engaged
2
3 Seconds
2 Flashes
3 sec Max time that starter will stay engaged
3*
5 seconds
3 Flashes
5 sec Max time that starter will stay engaged
1
Active Starter Kill
1 Flash
On when locked, Before ignition and 2 seconds after ignition turns off.
2
Passive Starter Kill
2 Flashes
Same as setting 1 but will arm 60sec after the ignition turns off.
3*
Bypass Module
3 Flashes
Output before ignition. Stays on 2 seconds after ignition turns off.
1
Safety ON
1 Flash
Must press the start button twice to remote start vehicle
2*
Safety OFF
2 Flashes
Press the start button once to remote start vehicle.
Press the Program Switch 4 times
to select setting 4 (This will be confirmed by 4 LED flashes)
Press and hold the Program
Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch.
Press the Program momentarily to move to next program step or repeat to change selection.
Press the Program Switch 5 times
to select setting 5 (This will be confirmed by 5 LED flashes)
Press and hold the Program
Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch.
Press the Program momentarily to move to next program step or repeat to change selection.
Press the Program Switch 6 times
to select setting 6 (This will be confirmed by 6 LED flashes)
Press and hold the Program
Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch.
Press the Program momentarily to move to next program step or repeat to change selection.
Press the Program Switch 7 times
to select setting 7 (This will be confirmed by 7 LED flashes)
Press and hold the Program
Switch until you receive the appropriate # of park light flashes and/or horn honks.
Release the Program Switch.
Press the Program momentarily to move to next program step or repeat to change selection.
Setting 4- Run Time
Setting 5-Maximum Crank Time
Setting 6- Starter Kill/ Bypass Module Output-
Orange wire on 14-Pin Con.
Setting 7- Safety Start Mode
PROGRAM MODE - STARTER SETTINGS
Enter STARTER Program Mode - See Page 7 for details on entering program mode
