12
GB/CY
Operation
is continually connected in the vehicle.
The minus pole of your battery is usually
connected to the car body of the vehicle.
Then disconnect the plus pole connection
cable (red) of the vehicle from the plus
pole of the battery.
Only then connect the “+” pole quick con-
tact connection terminals (red)
5
of the
car charger to the “+”-pole of the battery.
Connect the “–”-pole quick contact-con-
nection terminal (black)
4
to the “–”-pole
of the battery. Connect the mains cable
7
of the car charger to the socket.
Note:
If the connection terminals are
connected correctly, the digital display
6
indicates the voltage and the “connected”
display lights up. In the event of reverse
polarity, the display will show 0.0 and the
reverse polarity LED
will light up in
red in the digital display
6
.
z
Disconnecting
Disconnect the device from the mains
current.
Disconnect the “–”-pole quick con-
tact-connection terminal (black)
4
from
the “–”-pole of the battery.
Disconnect the “+”-pole quick contact-
connection terminal (red)
5
from the
“+”-pole of the battery.
Reconnect the plus pole connection
cable of the battery to the plus pole
of the battery.
Reconnect the minus pole connection
cable of the battery to the minus pole
of the battery.
z
Select charging mode
and start charging process
You can choose from different charging
modes to charge different batteries.
As compared to conventional car battery
chargers, this device has a special function
for reuse of a flat battery/rechargeable
battery. You can recharge a completely
discharged battery/rechargeable battery.
Protection against wrong connection and
short circuit ensures safe charging. The
integrated electronics do not start the car
battery charger at once after connection of
the battery, but only after a charging mode
has been selected.
If the connection terminals are connected to
the battery and the device is connected to
the mains, the digital display
6
will show
the “Connected” display. Once the charging
mode has been selected with the charge
start button
3
, the “Charging” display will
light up. When charging is complete, the
“Charged” display lights up.
If the digital display “0.0” is continually lit
before the battery is completely charged,
there is a defect.
In this case, check again if the connection
terminals
4
,
5
are correctly attached to
the battery and whether the correct bat-
tery type has been chosen. If the display
continually shows “0.0”, there may be a
defect in the battery.
Reactivation function /
reconditioning:
If a voltage between 8.5 V
and 10.5 V is detected in the connected
battery, the device will automatically start a
reconditioning process in order to reactivate
the battery. If a voltage between 8.5 V and
10.5 V is measured after the reconditioning
process, then “Err” will be shown on the
digital display. In this case, the battery is
faulty and must be replaced.
Note:
This function is only available
for 12 V batteries.
Digital display button
1
:
Enables the
switch between the digital display of the
voltage and charging progress in percent
322265_Kfz-Ladegerät_mit_Starthilfefunktion_ULG_17_A1_content_LB7.indb 12
22.05.2019 09:26:00
Содержание ULG 17 A1
