The output A0v
should
be switched off
and
the outputs
A1 and
A2 should
be switched on. Furthermore,
the
second dimming for A2 (A2-P2) should
be
switched on
and the CROSS
bit
should
be
set.
These outputs should only be activated if the loco moves backwards (
Drive.), the
function key
F14
is switched on
and the
function key F0 is switched off
Bank 2, line 17
-> CV31 = 8,
CV32 = 1
Four CVs for output and three CVs for conditions to program
Lok fährt (
Fahr.
) -> CV-Nummer = 256 + (17 - 17) * 16
+ 1 = 257 Lok fährt (
Fahr.
) -> Byte 1, Bit 6 = 1 -> CV
257 = 64
F14 key
on
> CV number = 256 + (17 - 17) * 16 + 3 = 259 key
F14 on
-> byte 3, bit 1 = 1 -> CV 259 = 2
Key
F0 switched off
+ loco reverse (previous) switched off
-
> CV number = 256 + (17 - 17) * 16 + 7 = 263
Key
F0 switched off
+ loco reverse (previous) switched off
-
> byte 7, bit 4 = 1 + bit 7 = 1-> CV 263 = 16 + 128 = 144
A0v
should be switched off
-
> CV number = 256 + (17 - 17) * 16 + 14 = 270
A0v
should be switched off
-
> byte 14, bit 0 = 0 -> CV 270 = 0
A1
+ A2
switched on -
> CV number = 256 + (17 - 17) * 16 + 13 = 269
A1
+ A2
switched on -
> byte 13, bit 0 = 1 + bit 1 = 1-> CV 269 = 1 + 2 = 3
A2-P2 switched on
-> CV number = 256 + (17 - 17) * 16 + 15 = 271
A2-P2 switched on
-> byte 15, bit 2 = 1 -> CV 271 = 4
CROSS
bit
set -
> CV number = 256 + (17 - 17) * 16 + 16 = 272
CROSS
-bit
set -
> byte 16, bit 0 = 1 -> CV 272 = 1
To facilitate programming, especially for extended function mapping, the programming software "Lok-Tool" can be
used, which is included with the digital programming and test station "DigiTest" from Uhlenbrock. This software is also
available for free download on our website www.uhlenbrock.de.
Second dimming of light and function outputs
The light and function outputs can be set to an alternative, ie second dimming (eg for a high beam). The settings of
the values for the alternative dimming are stored in the CVs 150 (light), 151 (A1) and 152 (A2). In the extended
function mapping (CV96 = 1), the alternative dimming of the CVs 150 - 152 is activated via the possible conditions
there (see "Extended function mapping).
Reset to factory setting (Reset)
To bring the decoder back to factory settings, two (CV8, CV59) can be used in the DCC programming, in the Moto-
rola programming a CV (CV59). In order to not rewrite all available areas, you can decide which areas should be
brought into factory settings. The value 1-4 to be programmed sets the following CVs to factory settings:
1 = CV0 - 256, and CV257 - 512 (RailCom®
Bank 7
)
CV31=0, CV32=255
2 = CV257 - 512
(RailCom Plus
®
Banken 5 & 6)
CV31=1, CV32=0 and CV31=1, CV32=1
3 = CV257 - 512
(extended function mapping banks 1 & 2)
CV31=8, CV32=0 and CV31=8, CV32=1
4 = CV257 - 512
(PWM modulation function outputs banks 3 & 4)
CV31=8, CV32=3 and CV31=8, CV32=4
