76
или изгасени всички открити пламъци.
Ако се установи теч на хладилен агент, който се изисква високотемпературно запо-
яване, всичкият хладилен агент трябва да се изтегли от системата или да се изоли-
ра (чрез спирателни кранове) в част от системата, която е отдалечена от мястото
на теча. Преди и по време на процеса на високотемпературно запояване системата
трябва да се продухва с азот, в който няма кислород.
Демонтиране и обезвъздушаване
Когато се прониква в контура на хладилния агент за извършване на ремонти или с
някаква друга цел, трябва да се използват стандартните процедури. При това оба-
че е важно да се спазва най-добрата практика, понеже трябва да се има предвид
запалимостта. Трябва да се съблюдава следната процедура:
• отстраняване на хладилния агент;
• продухване на контура с инертен газ;
• обезвъздушаване;
• повторно продухване с инертен газ;
• отваряне на контура чрез рязане или високотемпературно рязане.
Хладилният агент за зареждане трябва да се върне в правилните цилиндри за въз-
становяване. Системата трябва да се продуха с азот, в който няма кислород, за
да се осигури безопасността на изсушителя. Може да се наложи процесът да се
повтори няколко пъти. За тази задача не трябва да се използва сгъстен въздух или
кислород.
Продухването се постига чрез заместване на вакуума в системата с азот, в който
няма кислород, с продължаване на пълненето, докато бъде постигнато работното
налягане, с последващо изпразване в атмосферата и накрая отново създаване на
вакуум.
Този процес се повтаря, докато в системата вече не е останал хладилен агент. Ко-
гато се използва последното зареждане с азот, в който няма кислород, налягането
в системата трябва да бъде изпуснато до атмосферното, за да може тя да работи.
Тази операция е жизнено важна, ако се извършва високотемпературно запояване
на тръби.
Трябва да е сигурно, че изходът за вакуумната помпа не е затворен за никакви из-
точници на запалване и че има вентилация.
Процедури за зареждане
В допълнение на стандартните процедури за зареждане трябва да се спазват след-
ните изисквания:
- Трябва да е сигурно, че при използване на зареждащо оборудване не се получа-
Содержание DH5020
