manualshive.com logo in svg

UDIAG CR700, Руководство пользователя

Поделиться
Скачать
UDIAG CR700 Скачать руководство пользователя страница 11

● Read Codes
● Freeze Frame Data
● Erase Codes
● Live Data
● I/M Readiness
● Vehicle Information
● Unit of measure

4.1 Read Codes

Read Codes menu lets you read stored codes, pending codes and 
permanent does found in the control unit. Typical menu options include:
●Stored Codes
● Pending Codes
● Permanent Codes
To read codes from a vehicle:
1.Press the Read hot key to directly read the codes from home screen. 
Or scroll with the UP/DOWN key to highlight Read Codes from 
Diagnostic Menu and press the OK key. 
2.Select Stored Codes/Pending Codes/ Permanent Codes and press 
the OK key to confirm.                     
3.A code list including code number and its description displays.

4.2 Erase Codes

There are two ways to erase codes:
● Press the Erase hot key to erase codes from home screen.
● Traditional way: select Erase Codes from the diagnostic menu.
1.Press the Erase hot key to directly erase the codes from the home 
menu. Or use the UP/DOWN key to highlight Erase Codes from 
Diagnostic Menu and press the OK key.
2.Follow the on-screen instructions and answer questions about the 
vehicle being tested to complete the procedure.
3.Check the codes again. If any codes remain, repeat the Erase Codes 
steps.

Содержание CR700



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды