Ublox SARA-R4 Series Скачать руководство пользователя страница 49

Страница: 49 / 307

SARA-R4/N4 series - AT Commands Manual

UBX-17003787 - R09

7 Network service

Page 49 of 307

7.7 Network selection cPACSP

+PACSP

SARA-R410M-01B SARA-R410M-02B SARA-R410M-52B SARA-R412M

Modules

SARA-N4

Syntax

PIN required

Settings saved Can be aborted

Response time Error reference

Attributes

full

Yes

+CME Error

7.7.1 Description

If the EF

CSP

(Customer Service Profile) is available the +PACSP URC is provided in the following cases:

• SARA-R4 / SARA-N4 - at the module registration
• SARA-R4 / SARA-N4 - whenever the SIM/USIM issues the REFRESH proactive command related to the

CSP

For further information, see the AT&T Device Requirements [

The EF

CSP

is available on SIM/USIM cards from AT&T mobile network operator.

7.7.2 Syntax

Type

Syntax

Response

Example

Read

AT+PACSP?

+PACSP<bit_value>

+PACSP1

URC

+PACSP<bit_value>

+PACSP0

7.7.3 Defined values

Parameter

Type

Description

<bit_value>

Number

PLMN mode bit value:
•

0: automatic network selection is forced (see

Notes

)

•

1: network selection mode unchanged (see

Notes

)

7.7.4 Notes

• If EF

CSP

is available, the PLMN mode bit forces the automatic network registration, according to the

+COPS

<mode> value which is loaded at boot from the selected profile (see the

Appendix B.1

and

). The

following table explains the behavior:

Autoregistration <mode>

PLMN mode bit <bit_value>

Autoregistration behavior

Automatic network selection

Disabled

Automatic network selection

Manual network selection (search for the PLMN
stored in the selected profile)

Disabled

SARA-R4 / SARA-N4

• The read command is not supported.

7.8 Channel and network environment descrUCGED

+UCGED

SARA-R410M-02B SARA-R410M-52B SARA-R412M

Modules

SARA-N4

Syntax

PIN required

Settings saved Can be aborted

Response time Error reference

Attributes

partial

+CME Error

7.8.1 Description

Enables the protocol stack and network environment information collection.

Содержание SARA-R4 Series




















































































































































































































































































































Результаты поиска

Содержание SARA-R4 Series

Отзывы:

Бренды по названию

Популярные бренды

Ublox SARA-R4 Series, Руководство по управлению

Результаты поиска

Содержание SARA-R4 Series

Отзывы:

Бренды по названию

Популярные бренды