Ublox SARA-R4 Series страница 292 Скачать руководство пользователя | Manualshive

Страница: 292 / 307

background image

SARA-R4/N4 series - AT Commands Manual

UBX-17003787 - R09

B Appendix: AT Commands List

Page 292 of 307

B.1 Parameters stored in profiles

The parameter settings of some commands can be stored in the profiles available in the memory module.

SARA-R4 / SARA-N4
To partially display these profiles, see the

command description. Not all the parameter setting are

displayed through

Some AT commands have a unique configuration for all the AT interfaces while for other AT commands it
is possible to set a different configuration for each AT interface: the "AT interface configuration sharing"
column in the next table provides this information.
Some AT command interfaces have a dynamic activation, which means they are not statically activated
at  boot  time  (MUX  AT  channel  is  activated  when  the  MUX  protocol  is  established,  USB  AT  channel  is
activated  if/when  the  USB  cable  is  plugged-in,  deactivated  when  it  is  removed).  Since  the  activation
reloads  the  AT  command  profile  from  NVM  for  the  activated  interface,  the  shared  "AT  interface
configurations" could be overwritten. It is suggested to reconfigure them at the requested value if an AT
command interface is dynamically activated.

The following table lists the AT commands which setting can be stored in the profiles with their parameters
as well as the factory-programmed values.

AT command

Description

AT interface
configuration
sharing

Factory-programmed value / Remarks

DCD status

No

1 (DCD enabled)

DTR status

No

1 (DTR enabled)

Flow control status

No

3 (RTS/CTS DTE flow control enabled)

DSR override

No

1 (DSR line set to ON in data mode and to OFF in command
mode)

Preferred message
format

Yes

0 (format of messages in PDU mode)

New message
indication

Yes

•

1 (discard indication and reject new received message URCs
when MT-DTE link is reserved)

•

0 (no SMS-DELIVER indications are routed to the TE)

•

0 (no CBM indications to the DTE)

•

0 (no SMS-STATUS-REPORTs are routed to the DTE)

•

0 (MT buffer of URCs defined within this command is
flushed to the DTE when >mode< 1...3 is entered)

Operator selection

Yes

•

0 (autoregistration enabled)

•

0 (operator expressed in long alphanumeric format)

•

FFFF (undefined PLMN to register when COPS=1)

DTE-DCE character
framing

No

•

SARA-R4 / SARA-N4 - 3, 1 (framing format: 8 data 1 stop, no
parity)

DTE-DCE local flow
control

No

2 (<DCE_by_DTE> on circuit 106 (CTS)), 2 (<DTE_by_DCE> on
circuit 105 (RTS))

Baud rate

No

•

SARA-R4 / SARA-N4 - 115200 (115200 b/s)

Power Saving (mode,
timeout)

Yes

0 (power saving disabled)

Echo status

No

1 (echo enabled)

Result code
suppression

No

0 (DCE transmits result codes)

Automatic answer

No

0 (automatic answering disabled)

Escape character
selection

No

43 (043 corresponds the '+' character)

Command line
termination
character

No

13 (0x0d corresponds to the carriage return character)

Response
formatting character

No

10 (0x0a corresponds to the line feed character)

Command line
editing character

No

8 (008 corresponds to the backspace character)

Connection
completion timeout

No

60

«
...
290
291
292
293
294
...
»

Содержание SARA-R4 Series




















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SARA-R4 Series

Бренд: CAME Страницы: 18

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 4

Бренд: CAME Страницы: 40

Бренд: CAME Страницы: 26

Бренд: CAME Страницы: 34

Бренд: CAME Страницы: 2

Бренд: Febco Страницы: 12

Бренд: Game ready Страницы: 21

Бренд: VAMP Страницы: 304

Бренд: Jabra Страницы: 3

Бренд: Magellan Страницы: 2

Бренд: National Instruments Страницы: 14

Бренд: National Instruments Страницы: 11

Бренд: Nauticam Страницы: 2

Бренд: National Instruments Страницы: 18

Бренд: National Instruments Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды