manualshive.com logo in svg

Ublox SARA-R4 Series, Руководство по управлению

Поделиться
Скачать
Ublox SARA-R4 Series Скачать руководство пользователя страница 303

SARA-R4/N4 series - AT Commands Manual

UBX-17003787 - R09

 

Related documents

Page 303 of 307

41.

GSM  04.60  -  Digital  cellular  telecommunications  system  (Phase  2+);  General  Packet  Radio  Service
(GPRS); Mobile Station (MS) - Base Station System (BSS) interface; Radio Link Control / Medium Access
Control (RLC/MAC) protocol

42.

3GPP TS 05.02 - Multiplexing and Multiple Access on the Radio Path

43.

EVK-G25H Evaluation Kit User Guide, Docu No GSM.G1-EK-09022

44.

3GPP TS 51.014 - Specification of the SIM Application Toolkit for the Subscriber Identity Module - Mobile
Equipment (SIM - ME) interface

45.

u-blox 5/6 Receiver Description including Protocol Specification, Docu. No GPS-SW-09017

46.

3GPP TS 27.010 V3.4.0 - Terminal Equipment to User Equipment (TE-UE) multiplexer protocol (Release
1999)

47.

LEON-G1 Audio Application Note, Docu No GSM.G1-CS-10005

48.

EVK-U12 EVK-U13 User Guide, Docu No 3G.G2-EK-10010

49.

LISA-U1 / LISA-U2 series System Integration Manual, Docu No UBX-13001118

50.

3GPP TS 22.060 - General Packet Radio Service (GPRS); Service description; Stage 1

51.

ETSI TS 102 223 - Smart cards; Card Application Toolkit (CAT)

52.

GNSS Implementation Application Note, Docu No UBX-13001849

53.

3GPP TS 25.306 - UE Radio Access capabilities

54.

RFC3267 - Real-Time Transport Protocol (RTP) Payload Format and File Storage Format for the Adaptive
Multi-Rate (AMR) and Adaptive Multi-Rate Wideband (AMR-WB) Audio Codecs

55.

EVK-G20 Evaluation Kit User Guide, Docu No GSM.G1-EK-11002

56.

LISA-U1 series Data Sheet, Docu No UBX-13002048

57.

RFC 792 Internet Control Message Protocol (

http://tools.ietf.org/html/rfc0792

)

58.

3GPP TS 22.002 - Circuit Bearer Services (BS) supported by a Public Land Mobile Network (PLMN)

59.

3GPP TS 22.067 - enhanced Multi Level Precedence and Pre-emption service (eMLPP); Stage 1

60.

LISA-U2 series Data Sheet, Docu No UBX-13001734

61.

AT&T: Device Requirements -- Requirements Document -- Document Number 13340 -- Revision 4.6 --
Revision Date 9/2/11

62.

3GPP TS 23.972 - Circuit switched multimedia telephony

63.

3GPP TS 24.615 Communication Waiting (CW) using IP Multimedia (IM) Core Network (CN) subsystem;
Protocol Specification

64.

3GPP TS 25.101 - User Equipment (UE) radio transmission and reception (FDD)

65.

3GPP TS 45.005 - Radio transmission and reception

66.

Common PCN Handset Specification v4.2

67.

SIM Access Profile - Interoperability Specification - Bluetooth Specification V11r00

68.

EVK-U20 EVK-U23 User Guide, Docu No UBX-13001794

69.

Maxim MAX9860 16-Bit Mono Audio Voice Codec datasheet, 19-4349; Rev 1; 9/09. Available from the
Maxim website (

http://datasheets.maxim-ic.com/en/ds/MAX9860.pdf

)

70.

3GPP TS 23.122 - NAS Functions related to Mobile Station (MS) in idle mode

71.

ETSI  TS  122  101  V8.7.0  (2008-01)  Service  aspects;  Service  principles  (3GPP  TS  22.101  version  8.7.0
Release 8)

72.

BS EN 16062:2015 Intelligent transport systems - ESafety - eCall high level application requirements
(HLAP) using GSM/UMTS circuit switched networks, April 2015

73.

3GPP  TS  26.267  V12.0.0  (2012-12)  eCall  Data  Transfer;  In-band  modem  solution;  General  description
(Release 12)

74.

3GPP TS 51.010-1 Mobile Station (MS) conformance specification; Part 1: Conformance specification

75.

RFC 959 File Transfer Protocol (

http://tools.ietf.org/html/rfc959

)

76.

RFC 2428 FTP Extensions for IPv6 and NATs (

https://tools.ietf.org/html/rfc2428

)

77.

SARA-G3 Audio Application Note, Docu No UBX-13001793

78.

LISA-U1 / LISA-U2 Audio Application Note, Docu No UBX-13001835

79.

3GPP TS 23.014 Support of Dual Tone Multi-Frequency (DTMF) signalling V11.0.0 (2012-09)

80.

EVK-G35 Evaluation Kit User Guide, Docu No UBX-13001792

81.

SARA-G3 Series Data Sheet, Docu No UBX-13000993

82.

SARA-G3 / SARA-U2 Series System Integration Manual, Docu No UBX-13000995

83.

ETSI TS 127 007 V10.3.0 (2011-04) AT command set for User Equipment (UE) (3GPP TS 27.007 version
10.3.0 Release 10)

Содержание SARA-R4 Series




















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды