Ublox NEO-D9S Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 52

background image

NEO-D9S - Integration manual

Rework

We do not recommend using a hot air gun because it is an uncontrolled process and can damage
the module.

Use of a hot air gun can lead to overheating and severely damage the module. Always avoid
overheating the module.

After the module is removed, clean the pads before re-applying solder paste, placing and reﬂow
soldering a new module.

Never attempt a rework on the module itself, e.g. by replacing individual components. Such
actions will immediately void the warranty.

Conformal coating

Certain applications employ a conformal coating of the PCB using HumiSeal® or other related
coating products. These materials aﬀect the RF properties of the GNSS module and it is important
to prevent them from ﬂowing into the module. The RF shields do not provide 100% protection for
the module from coating liquids with low viscosity. Apply the coating carefully.

Conformal coating of the module will void the warranty.

Casting

If casting is required, use viscose or another type of silicon pottant. The OEM is strongly advised to
qualify such processes in combination with the module before implementing this in the production.

Casting will void the warranty.

Grounding metal covers

Attempts to improve grounding by soldering ground cables, wick or other forms of metal strips
directly onto the EMI covers is done at the customer’s own risk. The numerous ground pins should
be suﬃcient to provide optimum immunity to interferences and noise.

u-blox makes no warranty for damages to the module caused by soldering metal cables or
any other forms of metal strips directly onto the EMI covers.

Use of ultrasonic processes

Some components on the module are sensitive to ultrasonic waves. Use of any ultrasonic processes
(cleaning, welding etc.) may cause damage to the GNSS receiver.

u-blox oﬀers no warranty against damages to the module caused by ultrasonic processes.

5.3 Tapes

shows the feed direction and illustrates the orientation of the NEO-D9Ss on the tape:

UBX-19026111 - R07

5 Product handling

Page 44 of 52

C1-Public

«
...
42
43
44
45
46
...
»

Содержание NEO-D9S





















































Отзывы:

Нет отзывов

Похожие инструкции для NEO-D9S

AllShare Cast Dongle

Бренд: Samsung Страницы: 2

Бренд: D-Link Страницы: 14

Бренд: STONEFLY Страницы: 48

CLICK PLUS C2-02CPU

Бренд: Automationdirect.com Страницы: 10

Бренд: Alesis Страницы: 46

Urban Wireless CC-VT240W

Бренд: Cateye Страницы: 15

Бренд: Endace Страницы: 51

Бренд: Paradyne Страницы: 10

ZyXEL ZyAIR B-120

Бренд: ZyXEL Communications Страницы: 20

Бренд: WAGO Страницы: 48

Бренд: Tait Страницы: 8

Бренд: C4i Страницы: 5

Бренд: Renesas Страницы: 746

Accelero TWIN TURBO II

Бренд: Arctic Страницы: 2

DVI-Vision-IP-Fiber

Бренд: G&D Страницы: 240

Бренд: Datum Страницы: 49

Бренд: ADS Technologies Страницы: 21

Бренд: IFM Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды