Ublox NEO-D9S Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 52

background image

NEO-D9S - Integration manual

Part

Recommendation

Comment

C2

Murata GRM033R71C103KE14

CAP CER X7R 0402 10N 10% 16V

TYCO, 0.25PF, PESD0402-140 -55/+125C

ESD protection diode on RF trace

Table 5: Recommended components for antenna supervisor

3.4.1 Antenna voltage control - ANT_OFF

Antenna status (as reported in UBX-MON-RF and UBX-INF-NOTICE messages) is not
reported unless the antenna voltage control has been enabled.

Enable the antenna voltage control by setting the conﬁguration item CFG-HW-
ANT_CFG_VOLTCTRL to true (1).

Result:

• UBX-MON-RF in u-center "Message View": Antenna status = OK. Antenna power status = ON
• ANT_OFF pin = active high to turn antenna oﬀ therefore the pin is low to enable an external

antenna.

Start-up message at power up if conﬁguration stored:

$GNTXT,01,01,02,ANTSUPERV=AC *00

$GNTXT,01,01,02,ANTSTATUS=INIT*3B

$GNTXT,01,01,02,ANTSTATUS=OK*25

ANTSUPERV=AC

indicates antenna control is activated

3.4.2 Antenna short detection - ANT_SHORT_N

Enable the antenna short detection by setting the conﬁguration item CFG-HW-
ANT_CFG_SHORTDET to true (1).

Result:

• UBX-MON-RF in u-center "Message View": Antenna status = OK. Antenna power status = ON
• ANT_OFF = active high to disable an external antenna therefore the pin is low to enable an

external antenna.

• ANT_SHORT_N = active low to detect a short therefore the pin is high (PIO pull up enabled to be

pulled low if shorted)

Start-up message at power up if conﬁguration is stored:

$GNTXT,01,01,02,ANTSUPERV=AC SD *37

$GNTXT,01,01,02,ANTSTATUS=INIT*3B

$GNTXT,01,01,02,ANTSTATUS=OK*25

ANTSUPERV=AC SD

(Antenna control and short detection activated)

Then if shorted (ANT_SHORT_N pulled low):

• UBX-MON-RF in u-center "Message View": Antenna status = SHORT. Antenna power status =

ON (Antenna power control power down when short has not been enabled = oﬀ by default).

$GNTXT,01,01,02,ANTSTATUS=SHORT*73

• ANT_OFF = active high therefore still low (still enabled as auto power down is not enabled)

UBX-19026111 - R07

3 Receiver functionality

Page 20 of 52

C1-Public

«
...
18
19
20
21
22
...
»

Содержание NEO-D9S





















































Отзывы:

Нет отзывов

Похожие инструкции для NEO-D9S

Бренд: DBM Страницы: 50

Network Video Recorders

Бренд: e-Line Technology Страницы: 34

SmartMedia Adapter PC Card REX-SMA01F

Бренд: Ratoc Systems Страницы: 75

Бренд: Salusfin Страницы: 6

Бренд: IOtech Страницы: 16

Бренд: ESD Страницы: 28

Бренд: Dolphin Страницы: 9

PCH1 T P Series

Бренд: Parker Страницы: 107

Бренд: Cervoz Страницы: 22

Quadro M6000 Sync

Бренд: Nvidia Страницы: 8

SiliconDrive SSD-P16G(I)-3100

Бренд: Silicon Systems Страницы: 108

Бренд: Nakayo Страницы: 119

JetStor NAS 724UX

Бренд: AC&NC Страницы: 117

Бренд: Intel Страницы: 26

Бренд: ZALMAN Страницы: 16

Бренд: ICP DAS USA Страницы: 31

ULTRIX-FM-NS-1RU

Бренд: Ross Страницы: 5

Xtreme Networked Boat

Бренд: Broadband Products Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды