UAS SMOGHOG SHM-C Series, Руководство пользователя

Страница: 10 / 36

reV: 16i
SMoGHoG
®
SHM Series Models
6
3.5 ELECTRICAL CONNECTION
the SHM is available with various controls configurations.
refer to the section headings below and follow the
section instructions that best align with your specific unit.
Multiple sections may apply to the same unit. the SHM
customer electrical connections are located on the rear
of the unit as shown in figure 1B. the supply voltage
and fLa will be noted on the nameplate. the blower and
pulse cleaning system controls are factory pre-wired for
operation. the touchscreen controls are also pre-wired for
the integral option, but require field wiring and connections
for the remote display enclosure option. Wiring diagrams
for the various SHM controls, blower arrangement and
supply voltage options are available within the appendix
of this manual. note that the SHM does not contain
the main disconnect or fuses for the supply power.
electrical installation should be completed by a qualified
professional and done in accordance with all applicable
codes and regulations.
Power cord and connection into unit will be supplied by
the customer.
unit is available in the voltages shown below:
TABLE 1
SHM Voltage and Full Load Amps
Note: When making the main power connections to the
unit, fan rotation check is not required.
VOLT PH
#
BLWR HZ RPM FLA XFMR
208 3 1 50-60 3370 6.5 ---
230 3 1 50-60 3370 5.7 ---
240 3 1 50-60 3370 5.5 ---
380 3 1 50-60 4200 6.7 ---
480 3 1 50-60 4200 5.5 ---
575 3 1 50-60 4200 --- 6kVA
208 3 2 50-60 3370 13.5 ---
230 3 2 50-60 3370 11.5 ---
240 3 2 50-60 3370 11.0 ---
380 3 2 50-60 4200 13.9 ---
480 3 2 50-60 4200 11.0 ---
575 3 2 50-60 4200 --- 10kVA
208 3 3 50-60 3370 18.9 ---
230 3 3 50-60 3370 16.4 ---
240 3 3 50-60 3370 15.5 ---
380 3 3 50-60 4200 19.1 ---
480 3 3 50-60 4200 15.5 ---
575 3 3 50-60 4200 --- 15kVA
FOR BASIC CONTROLS ON SHM-11, SUBTRACT
0.5 AMP FROM FLA VALUES ABOVE.
TABLE 2
Wire Diagrams
3.5.1 ELECTRICAL SUPPLY POWER
the main power supply is connected to the SHM unit
through a 1˝ FNPT coupling located on the rear of the
unit shown in figure 1B. after feeding wires through the
coupling, terminations are made on the main bus bar
terminal for each phase and frame ground connection. the
rear electrical panel also contains the unit circuit breakers
and dc power supply for the controls components.
utilize table 1 for wire, fuse and disconnect sizing for
your respective product model. A second plugged 1˝
fnPt coupling is also located on the rear of the cabinet
for low optional voltage connections using the Machine
interlock feature to automate operation. ensure that the
rear electrical panel cover is in place and secured prior to
operating the unit. refer to the electrical wiring diagrams
in table 2 for additional wiring information.
3.5.2 ELECTRICAL BASIC CONTROLS
the basic electrical controls consist of a thermal motor
protection disconnect on the side of the unit. this is set
for the fLa of the single blower motor. this is factory
prewired to the blower motor. When installing this unit in
the field the customer will connect their factory power to
the disconnect on the line side of the thermal protector.
the disconnect on/off will supply power to the unit and
allow the blower on/off switch on the front of the unit to
control the blower. inside the door on the front of the unit
there is a blower speed adjustment. this will control the
speed of the blower from off to full speed. this should
be adjusted by the customer to meet their process
requirements.
Descrip�on of Wire Diagram
Appendix
Basic Controls A1
Remote Panel Basic Controls A2
One Blower & Controls A3
Two Blower & Controls A4
Three Blower & Controls A5
Remote Panel Touch Controls A6
One Blower & Remote Controls A7
Two Blower & Remote Controls A8
Three Blower & Remote Controls A9
Transformer 575:480 A10