U.S.SAWS CORE EZ Скачать руководство пользователя

Страница: 9 / 14

OPERATION

Waterworks

Division

P: 866 987-7297 F: 813-621-7125

Visit us at www.ussaws.com

[email protected]

Vertical Drilling Floors

Horizontal Drilling Walls

• Remove the entire machine out of the drilling loca-

tion (ex. cored hole) and place in a secure location for

disassembly.

• Reverse feed nut, counterclockwise, to remove core bit

and guide post.

• To remove core & anchor from guide post, strap chain

wrench to core and apply opposite pressure with the 1

• Unthread feed tube to remove the coring unit and leave the

core and guide post in the hole.

•

Re-stretch the anchor hole by pushing firmly on the guide post

(similar to original tightening procedure).

• Unthread guide post.

• Remove core from hole.

WARNING:

Do not over reach, maintain control. Keep proper footing

and balance at all times. Maintain a firm grip. Use extra care using

the tool on ladders, roofs, scaffolds, etc.

6.10

DISASSEMBLY STEPS

6.11 TROUBLESHOOTING

6.10.1 STEP 1

Stop motor, unplug unit from power, and turn off water.

6.10.2 STEP 2

Remove the core.

Based on job site conditions there are several ways to

remove the core. See full instructions to the left.

6.11.1 HOW TO REMOVE A JAMMED CORE BIT

Occasionally a sliver of steel/metal can jammed the core

bit. For instructions on to remove a jammed core bit, go to https://

youtu.be/U0PYPoatK44 or scan the QR code below with your smart

phone for a quick video “How To” instruction.

Содержание CORE EZ















Результаты поиска

Содержание CORE EZ

Отзывы:

Похожие инструкции для CORE EZ

Бренды по названию

Популярные бренды

U.S.SAWS CORE EZ, Руководство по эксплуатации

Результаты поиска

Содержание CORE EZ

Отзывы:

Похожие инструкции для CORE EZ

Бренды по названию

Популярные бренды