U.S.SAWS CORE EZ Скачать руководство пользователя

Страница: 1 / 14

08-30-2020

Waterworks

Division

P: 866 987-7297 F: 813-621-7125

Visit us at www.ussaws.com

[email protected]

U.S.SAWS CORE EZ

OPERATING MANUAL

TO PREVENT SERIOUS INJURY DO NOT OPERATE SAW WITHOUTPROPER TRAINING AND.

UNDERSTANDING OF THE OWNERS MANUAL

WHEN OPERATING THIS MACHINE

ALWAYS WEAR SAFETY APPROVED

HEARING PROTECTION

EYE OR FACE PROTECTION

PROTECTIVE HELMET

PROTECTIVE GLASSES OR FULL FACE PROTECTION

WEAR HAND PROTECTION

WARNING: Improperly maintaining the JS including the Honda engine or failing to correct a problem before

operation could cause a malfunction resulting in a serious injury. Always perform a pre-operation inspection before

each operation and correct any problem. See Honda Engines Owner's Manual.

5.2

Check the condition of the Honda engine. See the section titled "Before operation - is your

engine ready to go?" in the Honda Engines Owner's Manual.

WARNING: Exhaust gas from gasoline engines contains dangerous carbon monoxide. Breathing it can cause

unconsciousness and even kill you. Always operate gasoline engine machines in a well-ventilated area. Do not

operate in areas where exhaust fumes could accumulate without wearing appropriate respiratory protection.

Consult your employer and OSHA regarding use of appropriate respirator for dangerous carbon monoxide

gases. See Figure 7.

EEnnggiinnee eexxhhaauusstt ccoonnttaaiinnss

ppooiissoonnoouuss ccaarrbboonn

moonnooxxiiddee ggaass.. Breathing

it could cause death.

Operate machine in well

ventilated area.

FFiigguurree 77 -- W

Waarrnniinngg llaabbeell -- eennggiinnee eexxhhaauusstt ccoonnttaaiinnss ccaarrbboonn m

moonnooxxiiddee ggaass

1111

Notice of Copyright Protection

means without the prior written permission of U.S.SAWS

U.S. English

Содержание CORE EZ















Результаты поиска

Содержание CORE EZ

Отзывы:

Похожие инструкции для CORE EZ

Бренды по названию

Популярные бренды

U.S.SAWS CORE EZ, Руководство по эксплуатации

Результаты поиска

Содержание CORE EZ

Отзывы:

Похожие инструкции для CORE EZ

Бренды по названию

Популярные бренды