U-Line U-CLR1215W-40B Скачать руководство пользователя | Manualshive

Страница: 17 / 53

background image

USER GUIDE

Grille - Plinth Installation 1

SAFETY •

INSTALLATION & INTEGRATION

• OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Grille - Plinth Installation

REMOVING AND INSTALLING GRILLE

WARNING

!

Disconnect electric power to the unit before
removing the grille.

When using the unit, the grille (plinth strip/base
fascia) must be installed.

WARNING

!

DO NOT touch the condenser fins (4). The
condenser fins are SHARP and can be easily
damaged.

Removing the grille

1. Disconnect power to the unit.

2. Loosen the two screws (1).

3. Remove grille (2) and grille cap (3) from unit.

Installing the grille

1. Make sure grille cap (3) is behind grille in slots (2)

provided in grille before attaching grille to unit.

2. Align cabinet and grille holes and secure, but do not

over tighten grille screws (1).

3. Reconnect power to the unit.

2

1

3

5

4

17

«
...
15
16
17
18
19
...
»

Содержание U-CLR1215W-40B






















































Отзывы:

Нет отзывов

Похожие инструкции для U-CLR1215W-40B

Бренд: acaia Страницы: 12

Бренд: Ice-O-Matic Страницы: 2

Бренд: Ice-O-Matic Страницы: 25

Hotel Dispenser CD 40030 Series

Бренд: Ice-O-Matic Страницы: 2

Бренд: Omcan Страницы: 12

Midori Sno-King 1888W

Бренд: Gold Medal Страницы: 12

Бренд: Welbilt Страницы: 32

Бренд: emerio Страницы: 49

Бренд: Kolice Страницы: 10

Бренд: LabelMill Страницы: 65

Бренд: Beper Страницы: 44

Бренд: Bloomfield Страницы: 24

MAGNIFICA EVO FEB292X

Бренд: DeLonghi Страницы: 28

Бренд: Nespresso Страницы: 12

Бренд: Magister Страницы: 16

Бренд: Koldfront Страницы: 14

Бренд: Swift Страницы: 17

Бренд: Klarstein Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды