U-Line 124BEV Скачать руководство пользователя

Страница: 42 / 69

USER GUIDE

Troubleshooting 2

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE •

SERVICE

CHECKING PRODUCT TEMPERATURE

To check the actual product temperature in the
unit:

1. Partially fill a plastic (nonbreakable) bottle with water.

2. Insert an accurate thermometer.

3. Tighten the bottle cap securely.

4. Place the bottle in the desired area for 24 hours.

5. Avoid opening the unit during the testing period.

6. After 24 hours, check the temperature of the water. If

required, adjust the temperature control in a small
increment (see CONTROL OPERATION).

Causes which affect the internal temperatures of
the cabinet include:

• Temperature setting.

• Ambient temperature where installed.

• Installation in direct sunlight or near a heat source.

• The number of door openings and the time the door is

open.

• The time the internal light is illuminated. (This mainly

affects product on the top rack or shelf.)

Digital Display

Shows 1-16 or 99

A factory test mode may be enabled. Adjust

the temperature to 99 and press the LIGHT

icon.

Product Is

Freezing.

Because product in contact with the rear

wall may freeze, ensure no product is

touching the rear wall.
Adjust the temperature to a warmer set

point.

Product Is Not

Cold Enough.

Air temperature does not indicate product

temperature. See CHECKING PRODUCT

TEMPERATURE below.
Adjust the temperature to a cooler set point.
Ensure unit is not located in excessive

ambient temperatures or in direct sunlight.
Ensure the door is closing and sealing

properly.
Ensure the interior light has not remained

on too long.
Ensure nothing is blocking the front grille,

found at the bottom of the unit.
Ensure the condenser coil is clean and free

of any dirt or lint build-up.

Problem

Possible Cause and Remedy

Содержание 124BEV






































































Результаты поиска

Содержание 124BEV

Отзывы:

Похожие инструкции для 124BEV

Бренды по названию

Популярные бренды

U-Line 124BEV, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание 124BEV

Отзывы:

Похожие инструкции для 124BEV

Бренды по названию

Популярные бренды