U-Line 124BEV Скачать руководство пользователя | Manualshive

Страница: 22 / 69

background image

USER GUIDE

Grille - Plinth Installation 1

u-line.com

SAFETY •

INSTALLATION & INTEGRATION

• OPERATING INSTRUCTIONS • MAINTENANCE • SERVICE

Grille - Plinth Installation

REMOVING AND INSTALLING GRILLE
(PLINTH STRIP/BASE FASCIA)

WARNING

!

Disconnect electric power to the unit before
removing the grille (plinth strip/base fascia).

When using the unit, the grille (plinth strip/base
fascia) must be installed.

WARNING

!

DO NOT touch the condenser fins. The condenser
fins are SHARP and can be easily damaged.

Removing the grille
(plinth strip/base fascia)

1. Disconnect power to the unit.

2. Loosen the two screws (1).

3. Remove grille (plinth strip/base fascia) (2) from unit.

Installing the grille

1. Align cabinet and grille holes and secure, but do not

over tighten grille (plinth strip/base fascia) screws (1).

2. Reconnect power to the unit.

1

2

22

«
...
20
21
22
23
24
...
»

Содержание 124BEV






































































Отзывы:

Нет отзывов

Похожие инструкции для 124BEV

Бренд: Caple Страницы: 23

Бренд: Omega Страницы: 8

Бренд: Wine Enthusiast Страницы: 9

Бренд: Beko Страницы: 95

Бренд: Igloo Страницы: 3

Бренд: La Sommeliere Страницы: 132

Бренд: Vinturi Страницы: 34

Бренд: Cuisinart Страницы: 20

Бренд: Exquisite Страницы: 10

Бренд: Haier Страницы: 376

Monogram ZIW30GNZAII

Бренд: GE Страницы: 24

Бренд: Vinotemp Страницы: 12

large VinoCellier

Бренд: Vinotemp Страницы: 16

Бренд: Vintec Страницы: 16

Бренд: Vintec Страницы: 16

Бренд: hestan Страницы: 80

Бренд: Bauknecht Страницы: 10

Бренд: ARDES Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды