background image

USER GUIDE

 Troubleshooting 1

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE • 

SERVICE

Troubleshooting

BEFORE CALLING FOR SERVICE

If you think your U-Line product is malfunctioning, read 
the OPERATING INSTRUCTIONS section of this guide to 
understand clearly the function of the control. 

If the problem persists, read the NORMAL OPERATING 
SOUNDS, TROUBLESHOOTING GUIDE and CONTROL 
OPTIONS sections below to help you quickly identify 
common problems, and possible causes and remedies. 
Most often, this will resolve the problem without the need 
to call for service. 

IF SERVICE IS REQUIRED

If you do not understand a troubleshooting remedy, or 
your product needs service, contact U-Line Corporation 
directly. Contact information appears on the rear cover of 
this guide.

When you call, you will need your product Model and 
Serial Numbers. This information appears on the Model 
and Serial number plate located on the upper right or rear 
wall of the interior of your product. 

CONTROL OPTIONS

On/Off: 

Press power key and unit will turn off or on.

Light:

 When applicable (Table: Basic Settings) hit the 

light key and light will remain on for 3 hours.

Change F to C:

 Hold up and down key for 5 seconds.

Showroom Mode: 

Hold Light and on/off for 5 seconds 

to enter showroom mode. To exit, power down unit by 
unplugging the unit. While in this mode, all keys can be 
pressed with no effect on operation. The degree symbol 
flashes to indicate the mode is active.

Sabbath Mode:

 Hold light key for 5 seconds to enter 

Sabbath mode. Press light key again to resume normal 
mode.

3 Hour Shutoff Mode (Silence Mode):

 Hold down 

and Power for 5 seconds.

NORMAL OPERATING SOUNDS

All models incorporate rigid foam insulated cabinets to 
provide high thermal efficiency and maximum sound 
reduction for its internal working components. Despite this 
technology, your model may make sounds that are 
unfamiliar. 

Normal operating sounds may be more noticeable because 
of the unit’s environment. Hard surfaces such as cabinets, 
wood, vinyl or tiled floors and paneled walls have a 
tendency to reflect normal appliance operating noises.

Listed below are common refrigeration components with 
brief description of the normal operating sounds they 
make. NOTE: Your product may not contain all the 
components listed.

• Compressor: The compressor makes a hum or pulsing 

sound that may be heard when it operates. 

• Evaporator: Refrigerant flowing through an evaporator 

may sound like boiling liquid. 

• Condenser Fan: Air moving through a condenser may 

be heard.

• Automatic Defrost Drain Pan: Water may be heard 

dripping or running into the drain pan when the unit is 
in the defrost cycle.

Содержание 1224RF


































Отзывы: