u-blox M9 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 95

background image

NEO-M9N - Integration manual

3.9.4.3 Interface

Several UBX protocol messages provide interfaces to the

AssistNow Autonomous

feature. They are:

• The CFG-ANA-USE_ANA item is used to enable or disable the

AssistNow Autonomous

feature.

When enabled, the receiver will automatically produce

AssistNow Autonomous

data for newly

received broadcast ephemerides and, if that data is available, automatically provide the
navigation subsystem with orbits when necessary and adequate. The CFG-ANA-* conﬁguration
group also allows for a conﬁguration of the maximum acceptable orbit error. See the next
section for an explanation of this feature. It is recommended to use the ﬁrmware default value
that corresponds to a default orbit data validity of approximately three days (for GPS satellites
observed once) and up to six days (for GPS and GLONASS satellites observed multiple times
over a period of at least half a day).

• Note that disabling the

AssistNow Autonomous

feature will delete all previously collected

satellite observation data from the ﬂash memory.

• The UBX-NAV-AOPSTATUS message provides information on the current state of the

AssistNow Autonomous

subsystem. The status indicates whether the

AssistNow Autonomous

subsystem is currently idle (or not enabled) or busy generating data or orbits. Hosts should
monitor this information and only power oﬀ the receiver when the subsystem is idle (that is,
when the

status

ﬁeld shows a steady zero).

• The UBX-NAV-SAT message indicates the use of

AssistNow Autonomous

orbits for individual

satellites.

• The UBX-NAV-ORB message indicates the availability of

AssistNow Autonomous

orbits for

individual satellites.

• The UBX-MGA-DBD message provides a means to retrieve the

AssistNow Autonomous

data

from the receiver in order to preserve the data in power-oﬀ mode where no battery backup is
available. Note that the receiver requires the absolute time (i.e. full date and time) to calculate

AssistNow Autonomous

orbits. For best performance it is, therefore, recommended to supply

this information to the receiver using the UBX-MGA-INI-TIME_UTC message in this scenario.

UBX-19014286 - R07

3 Receiver functionality

Page 39 of 95

C1-Public

«
...
37
38
39
40
41
...
»

Содержание M9
































































































Отзывы:

Нет отзывов

Похожие инструкции для M9

Бренд: NAD Страницы: 14

Бренд: Sansui Страницы: 5

Бренд: R&S Страницы: 232

Бренд: XIEGU Страницы: 20

Бренд: XIEGU Страницы: 17

Skyrider Defiant SX24

Бренд: Hallicrafters Страницы: 9

Бренд: Transition Networks Страницы: 1

Бренд: Clarion Страницы: 162

Бренд: Harman Kardon Страницы: 28

Бренд: Onkyo Страницы: 60

Бренд: Pyle Страницы: 9

Бренд: Linx Страницы: 24

Бренд: Marantz Страницы: 60

Бренд: STONEX Страницы: 49

Бренд: SXblue GPS Страницы: 19

Бренд: Xoro Страницы: 106

Бренд: REI Страницы: 6

Бренд: Kia Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды