2
3
BLUETOOTH STEREO TOWER
SPEAKER WITH FM PLL RADIO
Please read following instructions prior to
operate your unit.
Manufacturer of this unit follows a principle
of continuous improvement and has no
responsibility for any changes that are made
to the unit nor any liability for these changes.
Thanks for your choice of our products.
MAIN UNIT
(see picture 1)
1. BLUETOOTH INDICATOR
2. POWER ON/STANDBY BUTTON
3. VOLUMe- BUTTON
4. BUTTON
5. TUNING/SKIP/SEARCH DOWN BUTTON
6. TUNING/SKIP/SEARCH UP BUTTON
7. PAIR/PLAY/PAUSE BUTTON
8. SOURCE BUTTON
9. LCD DISPLAY
10. ReMOTe SeNSOR
11. AUX IN JACKS
12. LINE IN JACK
13. ReSeT BUTTON
14. AC CORD
REMOTE CONTROL
(see picture 2)
1. SOURCE BUTTON
2. MUTE BUTTON
3. MeMORY BUTTON
4. MeM- BUTTON
5. NUMERIC BUTTONS
6. BaSS +/- BUTTONS
7. /- BUTTONS
8. POWER ON/STANDBY BUTTON
9. PAIR/PLAY/PAUSE BUTTON
10. MO/ST BUTTON
11. MEM+ BUTTON
12. CLOCK BUTTON
13. SLeep BUTTON
14. TUNING/SKIP/SEARCH UP/DOWN
BUTTONS
15. /- BUTTONS
POWER SUPPLY
Plug AC plug into the outlet socket for
connecting the main power.
Note: During playback, if not any operation in
about 6 hours, the unit will switch to standby
mode automatically.
SLEEP TIMER SETTING
You can set the sleep timer at power on
modes as following instructions:
Press SLEEP button on the remote control
repeatedly to cycle through the sleep time
options:
90 -> 80 -> 70 -> 60 -> 50 -> 40 -> 30 -> 20
-> 10 -> OFF
After the sleep time setting, you can play the
unit freely. Once the sleep time is expired, the
unit will be switched off.
During playback, press SLEEP button once to
check the remaining sleep time.
HOW TO SET TIME
At the standby mode, press and hold CLOCK
button on the remote until CLK“ shows on
the screen; use TUNING UP/DOWN button
on the remote to adjust the hour and conirm
your adjustment by pressing CLOCK button
on the remote; Minute starts blinking on the
screen, press TUNING UP/DOWN button on
the remote to set the minute accordingly, press
CLOCK button on the remote again to conirm
your setting.
During playback, press CLOCK button to
check the current time.
Note: The time only could be set on standby
mode.
BLUETOOTH OPERATING
This unit can receive stereo audio signal from
a BLUETOOTH stereo audio source device.
1. Power on the unit, switch to BLUETOOTH
mode by pressing SOURCE repeatedly.
2. Bluetooth LED indicator rapid blinking while
it is pairing.
3. pair and connect to Fa-1922 on the
BLUETOOTH audio source device. If
prompted for passcode, enter “0000”.
4. Pairing successful (LED indicator blue
lights up), ready to stream music.
5. During playback, press TUNING UP/
DOWN button to skip to the next or
previous track. Press and hold TUNING
UP/DOWN button to fast forward or
backward.
NOTE:
• pairing mode is canceled about 1.5
minutes when there is no devices for
pairing.
• The above are generic steps to pair a
BLUeTOOTH device, for more speciic
instructions on BLUETOOTH connectivity
for your device, please consult your
manufacturer’s manual.
• Once the unit enters to the BLUeTOOTH
mode, it will connect to the last
paired external BLUETOOTH device
automatically.
RE-CONNECT TO THE BLUETOOTH
AUDIO SOURCE DEVICE
If the device is already paired with the
Fa-1922, but became unconnected even with
both Bluetooth devices turned on. You can re-
connect them by following steps:
1. press and hold the paIR button to re-link
the audio source device. The Bluetooth
indicator will blink for about 1.5 minutes for
connecting.
2. Select Fa-1922 on the audio source device
for connecting. Bluetooth indicator will turn
to solid blue if the Fa-1922 and the device
have been re-connected successfully.
3. You can also re-connect the Fa-1922 by
using Bluetooth operation of the device to
be connected.
FM RADIO
TUNING THE FM RADIO
1. Power on the unit, switch to TUNER
(RADIO) mode by pressing SOURCE
repeatedly.
2. press TUNINg Up/DOWN button to ine
tune radio station. Press and hold TUNING
UP/DOWN button to auto search radio
station forward or backward respectively
(When an available station will be found,
the unit will broadcast it immediately and
the searching will be stopped).
3. at radio mode, it is possible to access
the frequency via numeric buttons on the
remote control. For example, press buttons
8, 9 and 8 to get to 89.8MHz; If access a
wrong frequency, eRROR“ will display on
the screen.
4. During radio playback, press MO/ST button
on the remote to switch between FM
STEREO and FM MONO modes.
STORING YOUR FAVORITE RADIO
STATION
1. During playback, press MEMORY button
on the remote for storing the current station
until memory cell number p01“ lashes on
the screen.
2. Use MeM+ or MeM- button on the remote
to select the corresponding memory cell
among p01-p20 for storing the station.
3. Conirm your selection by pressing
MEMORY button on the remote.
4. During radio playback, press MEM+ or
MeM- button on the remote repeatedly to
recall the stored stations.
MUTE THE UNIT
During playback, press MUTE button to
switch off the audio. Press the button again to
resume the audio.
VOLUME LEVEL/TREBLE/
BASS ADJUSTMENT
press /- button or /-
button or BaSS +/- button to adjust the volume
output level or treble effect or bass effect.
RESET BUTTON
When using the unit, you will come across
some problems that the unit doesn‘t work or
halt accidentally; you can use a needle or a
small, slender implement to poke the RESET
button in the rear of the player, the unit will
turn off automatically and then please reboot
the unit, the unit will recover the factory preset
condition.
CONNECTING WITH
OTHER APPLIANCES
(see picture 3)
AUX IN
1. Connect the AUX IN jacks on the unit to
audio source, for example, DVD player with
an RCA cable.
2. Press the POWER button on the unit or
STANDBY button on the remote to turn the
unit on.
3. press the SOURCe button repeatedly to
switch to AUX mode.
4. Use the native controls on the connected
audio device to begin playing music
through the connected unit.
LINE IN
Follow steps to connect the unit to another
audio device:
1. Connect the device into the player LINE
IN jack with the LINE OUT cable (not
included).
2. Press POWER button on the unit or
STANDBY button on the remote to turn the
unit on.
3. press SOURCe button repeatedly to
switch the unit to Line In mode.
4. Power on the device and begin play.
CAUTION
• The apparatus shall not be exposed to
dripping or splashing and that no objects
illed with liquids, such as vases, shall be
placed on the apparatus.
EN
G
L
ISH
EN
G
L
ISH
