Tymetal Corp. TYM 1000 Скачать руководство пользователя

Страница: 9 / 38

TYM 1000/2000 Slide Gate Operator Installation Guide

- 7 -

Rev 9 02/14

Operator Setup (Continued)

Limit Nuts Rough Adjustment

The limit nuts are not preset at the factory and must be

adjusted for the length of the gate in each installation. The

limit switches are activated by two threaded nylon rotary

limit nuts which are attached to a threaded limit shaft

driven by a chain and sprockets from the main drive shaft

(see Figure 10).

REMOVE THE CARDBOARD FILLER

BEFORE ADJUSTING THE LIMIT NUTS.

The Controller is factory set for right hand installations. The

left limit nut is for

OPEN

and the right limit nut is for

The limit nuts flip their definition in left hand installations.

(see left-right hand programming on Page 12).

With the gate connected to the gate operator in a mid-

travel position, the power disconnect switch turned OFF,

disconnect the operator by using the manual disconnect

lever. Once the operator has been disconnected,

manually move the gate by hand to within a foot of its

fully open position (the foot of distance is necessary to

allow for coasting of the operator after the limit switch is

tripped).

2. Once the gate is in this position, adjust the OPEN limit

nut until it activates the limit switch for open. Press down

the detent plate and rotate the nut along the threaded

shaft (see Figure 10).

3. After setting the open limit, move the gate to one foot

from fully closed and repeat the process for the CLOSE

limit nut (see Figure 10).

Limit Nuts Fine Adjustment

After finishing the rough limit nut adjustments, reposition the

gate to approximately the center of travel.
1.  Re-engage the operator using the disconnect handle.
2.  Turn the power disconnect switch ON.
3.  Stand clear of any moving parts and press the OPEN

button.

4. After the gate opens, press the CLOSE button.
5. Observe the gate in both directions as it runs through

each complete cycle. Adjust the open or close limit

nuts again if necessary. Fine levels of adjustment can

be made by adjusting a few teeth on the nut at a time.

If the gate stops during travel, you may need to adjust

the Open or Close Current Setting or the Maximum Run

Timer (see Pages 13-14).

PRESS DETENT

PLATE DOWN

ROTATE
LIMIT NUT

Figure 11. Setting the Limits

CAUTION

If the operator is installed in a left-hand installation. Set

the Controller to left-hand operation BEFORE running the

operator for the fine setting of the limit nuts. Failure to do so

will result in over-shooting the limit switches, and can cause

damage to the operator and/or gate. Refer to programming

on Page 12.

Figure 10. Limit Box Assembly

NOTE: Auxiliary limit switches are located below limit shaft

and can be used for gate status.

Left-Hand To Open

Right-Hand To Open

Limit Shaft

Limit Nuts

CLOSE LIMIT

OPEN LIMIT

CLOSE LIMIT

Auxiliary Limit Switches

Содержание TYM 1000







































Результаты поиска

Содержание TYM 1000

Отзывы:

Похожие инструкции для TYM 1000

Бренды по названию

Популярные бренды

Tymetal Corp. TYM 1000, Руководство по установке

Результаты поиска

Содержание TYM 1000

Отзывы:

Похожие инструкции для TYM 1000

Бренды по названию

Популярные бренды