manualshive.com logo in svg

Tymetal Corp. TYM 1000, Руководство по установке, Страница: 25 / 38

Поделиться
Скачать
Tymetal Corp. TYM 1000 Скачать руководство пользователя страница 25

TYM 1000/2000  Slide Gate Operator Installation Guide 

- 23 -

 

Rev 9 02/14

Tymetal’s Model MGT Gate Reversing Edge Transmitter is 

compatible with the APeX Controller used in Tymetal’s swing 

and slide gate operators. The MGT transmitter is designed 

to connect to normally open gate edge contacts and is fully 

supervised.
During normal operation, when the edge contact detects an 

obstruction  while  the  gate  is  moving,  the  MGT  transmitter 

will send an obstacle signal to the APeX Controller and stop 

or reverse the gate.
Being supervised, the MGT transmitter sends 

hourly

 status 

reports. It also sends trouble signals to the APeX Controller 

when  the  transmitter  detects  a  trouble  condition.  When  a 

trouble signal is sent to the APeX Controller, the run alarm 

sounder will beep fast and continue beeping for five minutes, 

then the sounder will chirp every five seconds while the gate 

is idle. 

To clear the trouble annunciation at the gate, the 

transmitter’s trouble condition must be corrected first, 

then the Controller’s power must be cycled off and on.

Four  conditions  regarding  the  MGT  transmitter  can  cause 

the APeX Controller to sound the audible trouble warning:

•  MGT transmitter case has been opened.
•  Disconnected or shortened reversing edge when MGT 

transmitter edge supervision is enabled.

•  Low batteries in the MGT transmitter.
•  Hourly supervision signals from the MGT transmitter 

have not been received by the controller.

MGT Transmitter Troubleshooting

When  troubleshooting  an  MGT  transmitter,  first  open  the 

MGT and check the unit’s internal indicators. The POWER 

indicator should light when the reversing edge is pressed or 

the TEST button is pressed. 

If it flashes, the batteries are 

low.

 The LOOP TROUBLE indicator will light when the TEST 

button is pressed 

if

 the SENSOR TEST jumper is enabled 

and

 the reversing edge wiring is open or shorted.

Tamper Supervision

The MGT transmitter contains a spring loaded tamper switch 

that detects if the case is open. When the case is opened, 

the transmitter will 

immediately

 send a trouble transmission. 

Anytime the transmitter is serviced, you will need to open the 

case. 

After closing the MGT case, cycle the Controller’s 

power to clear the trouble annunciation.

Edge Supervision

MGT  transmitters  can  monitor  the  connection  to  the  gate 

edge  if  the  gate  edge  is  equipped  with  an  internal  100µf 

capacitor.  There  is  a  jumper  in  the  MGT  that  enables  or 

disables  the  gate  edge  connection  monitoring.  If  edge 

monitoring is enabled, and the connection to the gate edge 

is open or shorted, the MGT will send a trouble transmission 

with the next hourly status report

 to the controller . 

Use 

the transmitter’s jumper to disable edge supervision 

if the reversing edge does not contain a capacitor (the 

trouble loop indicator stays lit in the MGT transmitter). 

The  jumper  does  not  affect  the  transmitter’s  hourly  status 

reports.

Low Battery Supervision

MGT  transmitters  monitor  their  battery  condition  and  will 

send  a  trouble  transmission 

with the next hourly status 

report

 to the Controller when the battery tests low. Replace 

the  batteries,  close  the  MGT  case,  and  power  cycle  the 

controller .

Status Supervision

MGT  transmitters  send 

hourly 

status  reports  to  the 

Controller. The Controller expects those hourly status reports 

(this cannot be disabled in the APeX Controller). When the 

controller  counts  four  missing  transmitter  status  reports, 

the  trouble  annunciation  will  occur.  This  could  occur  from 

transmitter trouble or poor radio reception by the controller.
Open  the  MGT  and  test  the  transmitter  by  viewing  it’s 

indicators  and  pressing  on  the  reversing  edge.  If  the 

transmitter tests OK, check the radio range of the Controller 

using  a  handheld  transmitter.  If  a  handheld  transmitter 

cannot reliable activate the operator at the distance the MGT 

is from the controller, remotely mount the local antenna or 

use an external receiver antenna (Model EXA-1000 or EXA-

2000). Also, Tymetal’s Model FT-1 Radio Interference Field 

Tester can be used to test the installation for abnormal radio 

interference conditions.

Using MGT Gate Reversing Edge Transmitters with the APeX Controller

MGT Gate Reversing Edge Transmitter

APeX Controller

Содержание TYM 1000







































Отзывы:

Нет отзывов