Tymetal Corp. TYM 1000 Скачать руководство пользователя страница 3

Страница: 3 / 38

TYM 1000/2000 Slide Gate Operator Installation Guide

- 1 -

Rev 9 02/14

Pre-installation Information

Before You Begin...

Before unpacking, inspect the carton for exterior damage. If you find

damage, advise the delivery carrier of a potential claim. Inspect your

package carefully. You can check your accessory box parts with the

enclosed packing slip for your convenience. Claims for shortages will be

honored for only 30 days from the date of shipment.
Before installing the operator, read this manual completely to ensure all

requirements for proper installation are present. Verify that the voltage to be

used matches the voltage of the operator.
If you have any questions about the requirements for proper installation

of this gate operator contact technical support at 800-328-4283

Always Check the Gate’s Action

It’s very important before installing the gate operator to

make sure the gate’s slides free and level throughout

the entire opening distance. If the gate does not

seem to operate properly, it may affect the operator

performance or greatly shorten the life of the unit. The

gate should also be designed so that airflow is ample to

prevent wind resistance and drag.

Gate Operator Classifications

All gate operators can be divided into one of four different classifications,

depending on their design and usage. Install this gate operator only

when the operator is appropriate for the construction and usage class

as defined below:

• Class I Residential Vehicular Gate Operator

A vehicular gate operator intended for use in a home or for one to

four single family dwellings with a common garage or parking area

associated with these dwellings.

• Class II Commercial / General Access Vehicular Gate

Operator

A vehicular gate operator intended for use in a commercial location or

building such as a multi-family housing unit of five or more single family

units, hotel, retail store or other building servicing the general public.

• Class III Industrial / Limited Access Vehicular Gate

Operator

A vehicular gate operator intended for use in an industrial location or

building such as a factory or loading dock area or other location not

intended to service the general public.

• Class IV Restricted Access Vehicular Gate Operator

A vehicular gate operator intended for use in a guarded industrial

location or building such as an airport security area or other restricted

access locations not servicing the general public, in which unauthorized

access is prevented via supervision by security personnel.

Approved Obstruction Detection Devices

The following contact or non-contact obstruction detection

devices have been approved for use with this slide gate

operator as part of a UL325 compliant installation:

• Contact Edges

Miller Edge Models MGO20, MGR20, MGS20, ME120

• Photoeyes

MMTC Model IR-55 (165’ range)

MMTC Model E3K (28’ range)

Safety Information and Warnings

Regulatory Warnings

Read the following before beginning to install this slide gate

operator:

WARNING

This type of warning note is used to

indicate possible mechanical hazards

that may cause serious injuries or death.

CAUTION

This type of warning note is used to

indicate the possibility of damage to the

gate or gate operator.

WARNING

This type of warning note is used to

indicate possible electrical shock hazards

that may cause serious injuries or death.

THE FOLLOWING FORMATS ARE USED FOR SAFETY NOTES

IN THESE INSTRUCTIONS.

IMPORTANT INSTALLATION

SAFETY INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF SEVERE

INJURY OR DEATH TO PERSONS,

REVIEW THESE INSTALLATION SAFETY

STEPS BEFORE PROCEEDING

1. READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS.

2. Read the yellow “Safety Instructions” brochure enclosed with the packet

of information. If any pages are missing or are unreadable, or you do not

have the safety instructions, please call Tymetal Corp. at 1-800-328-4283

to request additional copies.

3. ALL ELECTRICAL CONNECTIONS TO THE POWER SUPPLY MUST

BE MADE BY A LICENSED ELECTRICIAN AND MUST OBSERVE ALL

NATIONAL AND LOCAL ELECTRICAL CODES.

4. A separate power-disconnect switch should be located near the operator

so that primary power can be turned off when necessary.

5. Install the enclosed warning signs on both sides of the gate. A minimum

of two (2) WARNING SIGNS shall be installed, one on each side of the

gate where easily visible.

6. Never reach between, through or around the fence to operate the gate.

7. Never connect a button station within reach of the gate or on the side of

the gate operator.

8. Do not adjust the operator controller’s current sensing feature too high. It

should be adjusted high enough to keep the gate from falsely triggering

the sensing, but no higher than necessary for the gate to operate. DO

NOT DEFEAT THE PURPOSE OF THIS FUNCTION!

9. You must install all required safety equipment.

10. UL325 Compliance requires the use of contact edges or photoelectric

controls on all automatic or remotely-controlled gate operators.

11. The operator is intended for installation only on gates used for vehicles.

Pedestrians must be supplied with a separate access opening. The

pedestrian access opening shall be designed to promote pedestrian

usage. Locate the gate such that persons will not come into contact with

the vehicular gate during the entire path of travel of the vehicular gate.

Содержание TYM 1000







































Результаты поиска

Содержание TYM 1000

Отзывы:

Tymetal Corp. TYM 1000, Руководство по установке, Страница: 3 / 38

Результаты поиска

Содержание TYM 1000

Отзывы: