TYAN S2098 Скачать руководство пользователя страница 27

Страница: 27 / 41

http://www.TYAN.com

3.5 – Integrated Peripherals

Options related to onboard peripheral features can be altered through the following:

On-Chip Primary PCI IDE

Enabled

Disabled

Enables or Disables onboard IDE
controller.

Primary Master/Slave PIO

Auto

PIO 1, 2, 3, 4

Changes PIO (Programmed I/O)
interface mode for HDD.

Primary

Master/Slave UDMA

Auto

UDMA 1, 2, 3, 4, 5

Changes UDMA (Ultra Direct
Memory Access) interface mode
for HDD.

On-Chip Secondary

PCI IDE

Enabled

Disabled

Enables or Disables onboard IDE
controller 2.

Secondary Master/Slave

PIO

Auto

PIO 1, 2, 3, 4

Changes PIO (Programmed I/O)
interface mode for HDD.

Secondary Master/Slave

UDMA

Auto

UDMA 1, 2, 3, 4, 5

Changes UDMA (Ultra Direct
Memory Access) interface mode
for HDD.

USB Controller

All Enabled

None

Toggles the use of onboard USB
ports.

USB Keyboard Support

Enabled

Disabled

Toggles the use of a USB
keyboard under DOS.

AC97 Audio

Auto

Disabled

Choose to detect onboard AC97
Audio by BIOS.

Onboard LAN Device 1

Enabled

Disabled

Enables or disables LAN 1
(10/100Mbit)

Onboard LAN Device 2

Enabled

Disabled

Enables or disables LAN 2
(Optional 10/100Mbit)

Init Display First

PCI Slot

Onboard

Selects the primary graphics card.

Содержание S2098










































Результаты поиска

Содержание S2098

Отзывы:

Похожие инструкции для S2098

Бренды по названию

Популярные бренды

TYAN S2098, Руководство пользователя

Результаты поиска

Содержание S2098

Отзывы:

Похожие инструкции для S2098

Бренды по названию

Популярные бренды