TYAN S1682D Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 29

background image

5

S1682D-001-02

1.3 Software Specifications

BIOS

• Award or AMI Plug 'n' Play flash BIOS

• Deep green and Energy Star compliant.
• ATX CMOS setup, BIOS/CHIPSET setup
and hard disk utility included.
• Support for easy BIOS upgrades with flash
chip.

Operating System

• Operates with MS-DOS, Windows 3.x, Win
dows for Workgroups 3.x, Windows 95,
Windows NT
• OS/2, Novell Netware, and SCO Unix, Linux.

Tyan is also a Solaris certified manufacturer.

1.4 Environment

Operating Temperature

0

o

to +55

o

C

Humidity

<80% @36C

o

Altitude

@10,000 feet (operating)

Vibration

0 to 1,000 Hz

Voltage

230 Watt ATX power supply

1.5. Manual Organization

Chapter 1 "Introduction" describes the features and performance of the S1682D
system.

Chapter 2 "Installation" describes the procedures of setting up the system board.
Also refer to this Chapter for detailed information about jumper settings.

Chapter 3 "Installation and Removal of the CPU" gives detailed instructions on
installation and removal of the latest Pentium II--Boxed and Passive CPU's.

If you encounter any problem, refer to Chapter 4 "Trouble-shooting", which
describes trouble-shooting procedures for the system.

Bus Slots

• Five 32-bit PCI Bus Master slots
• Three ISA Bus Slots
(One ISA and one PCI shared
slots)

«
...
3
4
5
6
7
...
»

Содержание S1682D






























Отзывы:

Нет отзывов

Похожие инструкции для S1682D

Бренд: u-blox Страницы: 25

Бренд: MINN KOTA Страницы: 14

Бренд: Supermicro Страницы: 2

MITX-DNV0 Series

Бренд: Quanmax Страницы: 84

Бренд: Avalue Technology Страницы: 79

Бренд: Gigabyte Страницы: 52

Бренд: Cebekit Страницы: 8

Бренд: Gigabyte Страницы: 72

Бренд: Ublox Страницы: 22

TLV320AIC12KEVM-K

Бренд: Texas Instruments Страницы: 40

AR6MXCS- Series

Бренд: BCM Страницы: 9

Z80 Super Bullet

Бренд: Wave Mate Страницы: 25

Kontron mITX-VR1000 V2.0

Бренд: S&T Страницы: 8

Бренд: Gigabyte Страницы: 92

73-30130-00877-9

Бренд: Kvaser Страницы: 16

Бренд: TYAN Страницы: 59

Бренд: HOLT Страницы: 14

Бренд: DFI Страницы: 102

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды