background image

Operation manual B10

16

  4.3    Operation

Operation of the B10A

 

speaker requires a DSP-Controller. TW AUDiO recommends opera-

ting the B10P loudspeaker on a DSP-Controller. For this purpose, only presets developed by 
TW AUDiO are recommended. The TW AUDiO system racks are ideally suited for this purpose.

Make sure that the amplifier’s specifications meet the requirements. Using an amplifier that 
doesn’t meet the specifications can destroy the loudspeaker.

Please note the technical data in section 3.1 on page 11.

NOTE

Before connecting the loudspeaker to the amplifier, ensure that the right preset has been 
loaded.

Using the wrong preset or a preset not provided by TW AUDiO preset can destroy the speaker.

NOTE

  4.4    Connecting the cable

To create a cable connection with an amplifier rack from TW AUDiO, proceed as follows.

Ensure that the cable cross sectional area is sufficient (at least 1.5 mm²) to avoid power losses.  
TW AUDiO recommends using the loudspeaker cables available from TW AUDiO. 

When connecting the cables to the loudspeaker, ensure that polarity (+/-) and pin assignment 
(1/2) are correct. Incorrect connection can lead to a significant change in the loudspeaker’s 
sound characteristics and may damage the driver.

The pin connections of the B10

 

loudspeaker can be found in section 3.2 (“Connection dia-

gram”) on page 11 and 12.

The internal wiring of the B10

 

loudspeaker allows for parallel connection of multiple loudspe-

aker units.

Please note that parallel connections will decrease the total impedance of your loudspeaker 
configuration.

The total impedance and the resulting power of the speaker configuration must match the 
output power of the amplifier.

NOTE

Содержание B10A





















Отзывы: