Tuthill M-D Pneumatics PD PLUS 17/46 Series Скачать руководство пользователя страница 4

Страница: 4 / 64

NOTE

Indicates a statement of information which, if not avoided, could cause
damage to the product.

CAUTION

Read manual before operation or bodily harm may result. Attention should
be given to the safety related sections of this manual.

2.2 DATA PLATE

WARNING

CAUTION

http://www.tuthill.com

Hearing protection

required.

Do not touch hot

surfaces.

)

(

READ INSTRUCTION MANUAL BEFORE OPERATION OR BODILY HARM MAY RESULT

Keep body & clothing away

from machine openings.

Do not operate without

guards in place.

Tuthill Vacuum & Blower Systems

4840 West Kearney Street

Springfield, Missouri USA 65803

YEAR

MAWP

MAX RPM

General Operation and Symbols on Data Plate - The following information is contained on the data plate:

WARNING

Keep body & clothing away from machine.

During operation, keep body and clothing away from inlet and outlet of the
blower.

WARNING

Do not operate without guards in place.

CAUTION

Hearing protection is required while the blower is in operation. Noise levels
may reach as high as 81 dBA.

CAUTION

Do not touch hot surfaces.

The upper limit of the blower operation is 400° F (205° C). Do not touch
the blower while it is in operation and assure blower is cool when not in
operation.

Содержание M-D Pneumatics PD PLUS 17/46 Series

































































Результаты поиска

Содержание M-D Pneumatics PD PLUS 17/46 Series

Отзывы:

Бренды по названию

Популярные бренды

Tuthill M-D Pneumatics PD PLUS 17/46 Series, Инструкция по установке, эксплуатации, обслуживанию и ремонту

Результаты поиска

Содержание M-D Pneumatics PD PLUS 17/46 Series

Отзывы:

Бренды по названию

Популярные бренды