manualshive.com logo in svg

Tuthill M-D Pneumatics PD PLUS 17/46 Series, Инструкция по установке, эксплуатации, обслуживанию и ремонту

Поделиться
Скачать
Tuthill M-D Pneumatics PD PLUS 17/46 Series Скачать руководство пользователя страница 14

14

5.3.3  HAZARDS ASSOCIATED WITH BREAKDOWN OR IGNITION OF LUBRICATION

DANGER

There is a risk associated with the lubrication media breaking down and 
resulting in a hazardous fl uid or vapor.  There may also be a hazard 
associated with the ignition of the lubrication media.  Refer to the lubrication 
manufacture’s applicable instruction for safety precautions.

5.4  PIPING CONNECTIONS

WARNING

Pipe loading on the blower should be negligible as pipe loading can cause 
distortion of the blower.  Use proper supports and pipe hangers to assure 
that there is no loading.

 

NOTE

Remove the protective covers from the inlet and outlet ports and inspect for 
dirt and foreign material.

Inlet and outlet connections on all blowers are large enough to handle maximum volume with minimum 
friction loss. Maintain same diameter piping. Silencers must not be supported by the blower. Stress loads 
and bending moments must be avoided.

Be certain all piping is clean internally before connecting to the blower. We recommend placing a 16-mesh 
wire screen backed with hardware cloth at or near the inlet connections for the fi rst 50 hours of use until the 
system is clean. Make provisions to clean the screen after a few hours of operation and completely discard 
it once the system is clean, as it will eventually deteriorate and small pieces going into the blower can cause 
serious damage. A horizontal or vertical air fl ow piping confi guration is easily achieved by rearranging the 
mounting feet position.

HAZARDS ASSOCIATED WITH HAZARDOUS PROCESS FLUIDS

DANGER

It shall be the responsibility of the installer to ensure that piping is adequate, 
sealing between pipe joints is adequate for the process fl uids and proper 
process and pressure protection devices are in place.  It is also the 
responsibility of the installer to assure that process gasses are not vented 
in a manner that would be hazardous.

Refer to the manufacturer of the process media to assure that proper safety 
precautions are in place.

5.4.1  BLOCKAGE OR RESTRICTION

WARNING

Damage to the blower could occur if there is blockage in the inlet or outlet 
ports or piping.  Care should be taken when installing the blower to assure 
that there are no foreign objects or restrictions in the ports or piping.

Содержание M-D Pneumatics PD PLUS 17/46 Series

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды