manualshive.com logo in svg

Tuthill AC, Инструкция по установке и обслуживанию

Поделиться
Скачать
Tuthill AC Скачать руководство пользователя страница 15

V1.4 

                                        15 of 22                                                    04/01/2009 

 

•

  Install the new stationary seat into the bearing cap. 

•

  Place the bearing cap on the shaft and slide into place. 

•

  Align the mounting holes and reinstall the bearing cap screws 

 
Changing Rotation

 

 

Model C1B pumps manufactured after 1996 are bi-directional and will work

 

equally well in 

either direction of rotation with no modification. Older C1B pumps are directional, carrying 
model designations of C1B-C or C1B CC. 
 
To change the rotation of these pumps: 

•

  Look at the pump from the shaft end with the ports up and note the location of the 

V notch in the bracket.  If at the top (12 o'clock), rotation is clockwise; if at the 
bottom (6 o'clock), counterclockwise. 

•

  • Remove the cover screws so that the bracket moves freely. 

•

  • Rotate the bracket 180°. 

•

  •  Align the mounting holes and reinstall the cover screws.  

 
 

 

If outfitted with an internal relief valve (model C1BV), these pumps become rotational. 
Rotation cannot be changed in the field unless the cover/valve assembly is replaced. 

To change the location of the suction port on pumps supplied with Tuthill's unique 
automatic reversing feature (model RC1B): 

•

  Remove the cover screws. 

•

  Rotate the cover 180° so that the boss on the cover points to the new suction 

(inlet) port. 

•

  Align the mounting holes and reinstall the cover screws. 

Model C1B 

V Notch 

Содержание AC























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды