manualshive.com logo in svg

Tuthill AC, Инструкция по установке и обслуживанию

Поделиться
Скачать
Tuthill AC Скачать руководство пользователя страница 13

V1.4 

                                        13 of 22                                                    04/01/2009 

 

•

  Apply a dab of petroleum jelly to the seal lip and install it over the shaft. (If the 

seal is EPR, apply a silicon-based lubricant). The seal lip must retain its position 
on the shaft. Work the housing cap assembly up and down the shaft to make 
certain the seal lip slides freely.  

•

  Align the holes in the housing cap with the holes in the bracket and reinstall the 

three screws. 

Changing Rotation - Models C1E and C1EN

 

Looking at the pump from the shaft end with the ports up, locate the short vent plug 
(painted red). This is the suction (inlet) side of the pump. If on the right side, rotation is 
clockwise; if on the left, counterclockwise. Behind this short vent plug is a small flow plug. 

•  Remove both the long and short vent plugs as well as the small flow plug (with a hex 

wrench). 

•  Interchange the locations of the short vent plug and flow plug with the long vent plug. 
 

 

 
 
 
 

 
 
 
 

 
 
Model C1 E, C1 EN 

If outfitted with an internal relief valve (models C1EV and C1ENV), the rotation cannot be 
changed in the field unless the cover/valve assembly is also replaced. 

To change the location of the suction port on pumps supplied with Tuthill's unique 
automatic reversing feature (models RC1E and RC1EN), the following must be done in 
addition to the steps above: 

•

  Remove the cover screws. 

•

  Rotate the cover 180° so that the boss on the cover points to the new suction 

(inlet) port. 

•

  Align the mounting holes and reinstall the cover screws. 

LONG VENT PLUG 

 

Gaskets

Содержание AC























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды