background image

 

Aqua

Flash U

ser’s Manual 

-

 

If the battery power is < 10%, the following message will display 

Battery 

Low Pwr! Replace Battery!

” you will not be able to make any 

measurements until batteries are replaced. 

 
2.3 Calibration Check 

 
The 

Aqua

Flash is factory calibrated and should remain calibrated for many years.  

Calibration can be checked using an Adjustable Solid Secondary Standard (SSS).  To check 
instrument calibration using a SSS: 
  

1  Press the ON/OFF button to turn the 

Aqua

Flash on and wait until the warm up has 

completed 

2  Press the CAL VAL button to see what the calibration value is set to 
3  Obtain an Adjustable Solid Secondary Standard (SSS) and loosen the small black 

locking hex screw located on the back of the SSS.  

4  Holding the SSS by the tab, insert it with the tab at the back of the sample 

compartment and close the sample compartment lid 

NOTE:  The AquaFlash should be on a flat surface when reading the 
Adjustable Solid Secondary Standard (SSS). 

5  Press the READ button 

a.  If the CHL value displayed is lower than the calibration value determined in step 

2, adjust the SSS to give you a larger response by rotating the silver hex screw 
located at the top of the SSS counterclockwise and re-read the SSS.   

b.  If the CHL value displayed is higher than the calibration value determined in step 

2, adjust the SSS to give a smaller response by rotating the silver hex screw 
located at the top of the SSS clockwise and re-read the SSS.   

6  Continue adjusting and reading the SSS until the CHL value displayed matches the 

calibration value +/-5% determined in step 2. 

7  When finished, tighten the locking screw on the back by turning clockwise to lock the 

SSS

’s response.  

8  Insert the SSS into the instrument. 
9  Press the CHK STD button.  

a.  If the setting is valid, the 

Aqua

Flash will display 

“Cal. Check Passed”. 

b. 

If the 

Aqua

Flash dis

plays “Cal. Check Failed”, repeat steps 3-9.

 

The SSS can now be used to periodically check for instrument drift and can be stored in the 
side pocket of the 

Aqua

Flash storage pouch.   

 

 

Содержание AquaFlash



















Отзывы: