background image

Aerator

 PRO-26

15

Chain  Idler  Adjustment:

 

The  chain  idler  sprocket 

(located under the side chain guard) can be adjusted 

to remove excess slack in the chain caused by chain 

wear  or  stretch.  Before  adjusting  idler  sprocket 

position, ensure that the chain and all sprockets have 

been cleaned and that the chain seats properly on the 

sprockets. A build–up of dirt on the sprockets or chain 

can  cause  the  chain  to  become  too  tight.  Inspect 

all  the  sprockets,  bearings,  and  the  chain  for  wear 

or  damage.  With  the  tine  reel  elevated,  loosen  the 

idler sprocket and adjust to the proper tension setting. 

Chain should have a up and down movement of 12 

mm to 25 mm (1/2” inch to 1” inch). Take measurement 

at a center point on the chain between the front drum 

sprocket  and  the  tine  reel  sprocket.  Retighten  idler 

sprocket and recheck tension setting measurement.

Clutch  Cable  Adjustment:

 

The  clutch  cable  has  an 

adjuster (located midpoint on the cable) to increase 

or decrease the V-belt tension. If the V-belt is slipping, 

the V-belt tension needs to be increased. If machine 

will not freewheel when the clutch is released, the V-

belt tension needs to be decreased. Before adjusting, 

inspect the V-belt, clutch cable, and the clutch cable 

spring for damage and wear. Replace any damaged 

or  worn  items. To  adjust  the  clutch  cable  for  V-belt 

slippage,  loosen  the  lock  nut  on  the  cable  adjuster 

and shorten the cable by turning the adjuster one turn 

at a time until slippage is corrected. Ensure that the 

machine  will  freewheel  when  the  clutch  is  released 

(belt guard must be on machine). Secure adjustment 

by  tightening  lock  nut  against  adjuster.  Test  and 

repeat adjustment if required. Replace V-belt if proper 

operation cannot be reached with cable adjustment.

SERVICE

How To Obtain Parts and Service

Contact TURFCO DIRECT to order parts or to arrange 

repair service.  For a list of authorized TURFCO dealers 

in  your  area,  or  for  additional  information  regarding  

Aerator PRO-26, direct inquiries to TURFCO DIRECT.

TURFCO DIRECT 

1655 101

st

 Avenue North East 

Minneapolis, MN  55449-4420  USA
Telephone (763) 785-1000 

FAX (763) 785-0556 

Internet - www.turfcodirect.com

 

E-mail - [email protected]

To  ensure  safety  and  proper  operation,  always 

purchase genuine TURFCO replacement parts from an 

authorized  TURFCO  dealer.  Replacement  parts  from 

other sources may damage the Aerator PRO–26 and/or 

create a safety hazard. Always refer repairs to properly 

trained service personnel.

DO NOT ALTER the Aerator PRO–26 in any manner. 

Unauthorized  alterations  may  affect  its  operation, 

performance, and may result in injury or death to the 

operator as well as other individuals in the work area.

Содержание 85395
















Отзывы: